manualshive.com logo in svg

BFM Europe Arana RC, Instruction Manual

Share
Download
BFM Europe Arana RC Instruction Manual Download Page 11

TO REPLACE THE BATTERY PACK

a)

Remove the fender and ashpan assembly. The battery holder is located

on the Right Hand side of the appliance .

b)

Remove the battery pack with care and then disconnect the battery lead

at the white rectangular plug.

c)

Replace in reverse order and check correct operation of the appliance.

NB

The handset uses one LR61 (9v) and should be replaced by

removing the cover on the rear of the handset.

ENSURE THE BATTERIES ARE CONNECTED TO THE CORRECT POLARITY

POSITVE (+), NEGATIVE (-)

REMOVAL / RE-FITTING THE TRIM

The trim is positioned on the firebox fixing flange and is secured with magnets.

USER REPLACEABLE PARTS

The only user replaceable parts on this fire are the fuelbed components and coals

which may be replaced as described in the above section. Replacement of any

other parts must be carried out by a competent person such as a GAS SAFE

registered gas installer.

The part numbers of the user replaceable parts are as follows, these are available

from BFM Europe, whose details can be found below.

Fuelbed base

B-58690

Fuelbed front rail

B-18730

Replacement coal set

B-58700

11

Summary of Contents for Arana RC













Reviews:

No comments

Brands by name

Popular brands

Load more brands