10-CHANNEL MIXING AMPLIFIER
EX-10 Pro
9
8
AUX2
/
FX
AUX1
AUX IN
MONITOR
FX
CD
/
CDR
MP3
HIGH
LOW
EFFECTS
EFF TO
MIX
GROUP
GROUP
GROUP TO
L
R
MIX
PHONES
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
5
4
MIX
GROUP
PK
GAIN
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
1
1
MIX
GROUP
PK
GAIN
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
2
2
MIX
GROUP
PK
GAIN
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
3
3
MIX
GROUP
PK
GAIN
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
4
4
MIX
GROUP
PK
GAIN
PAD
AUX2
/
FX
HIGH
MID
LOW
AUX1
R
L
PAN
6
4
MIX
GROUP
PK
GAIN
AUX2
/
FX
MID
LOW
AUX1
R
L
PAN
7
/
8
STEREO
7
/
8
STEREO
MIX
GROUP
PK
GAIN
AUX2
/
FX
MID
LOW
AUX1
R
L
PAN
9
/
10
STEREO
9
/
10
STEREO
MIX
GROUP
PK
GAIN
+48V 5-6
+48V 1-2
+48V 3-4
14
CONTROLS AND FUNCTIONS
Amplifier
AUX2/FX CONTROL:
Adjusts effector volume input
signal. Aux 2 is ideal for sending a signal to outboard
processors.
AUX1 CONTROL:
Auxiliary Convey. Set the stereo signal
from outside and control through stereo and mono
channel. Aux 1 is ideal for sending a signal to monitors
or headphone amplifiers.
PAD SWITCH:
This switch is for microphones and
balanced line-level signals that produce a higher output
than usual may require that the gain control is turned way
down. When it is not used, you should push the switch to
disengaged state ( ). When it is used, you should push
the switch to engaged ( ). This prevents overloading the
microphone preamp and provides better gain control.
The pad only applies to XLR inputs, not the ¼” TRS inputs.
EQUALIZER (HIGH, MID and LOW):
Adjusts the
channel’s high, mid, and low frequency bands. Setting
the knob to the “0” position produces a flat response in
the corresponding band. Turning the knob to the right
boosts the corresponding frequency band, while turning
to the left attenuates the band.
GAIN CONTROL:
Adjusts the input signal level. To get
the best balance between the S/N ratio and the
dynamic range, adjust the gain so that the PEAK
indicator 9 lights on the LEVEL METER only occasionally
and briefly on the highest input transients. The -60 to +10
scale is the MIC input adjustment range. The 40 to +10
scale is the LINE input adjustment range.
FRONT PANEL:
1
2
3
4
5
6
7
8
9
10
11
PEAK
LED LIGHT:
It lights up when an optimum
operating level has been adjusted.
GAIN CONTROL:
Adjusts the input signal level. To get
the best balance between the S/N ratio and the
dynamic range, adjust the gain so that the PEAK indicator
9 lights on the LEVEL METER only occasionally and briefly
on the highest input transients. The -60 to +10 scale is the
MIC input adjustment range. The 40 to +10 scale is the
LINE input adjustment range.
USB/SD PLAYER CONTROL PANEL:
A. PLAY-MUSIC CONTROL
B. LCD DISPLAY:
USB/SD status display.
C. REPEAT MUSIC, RECORD MUSIC, SYNC
BLUETOOTH SETTING FUNCTIONS
F. USB SLOT
EFFECTOR CONTROL PANEL:
D. LCD DISPLAY:
Effector status display.
E. PROGRAM:
Use the program control to select one of
the built-in effects. For details about available effects,
refer to the “Effect Programs” on page 17.
MAIN CHANNEL AUDIO OUTPUT LED DISPLAY:
Show
the effect level stronger and
strength of the signal.
POWER LIGHTS:
Power Indicator red lights up when the
mixing amplifier's power is ON.
7
3
6
5
4
2
1
USB
01-HALL 1
02-ROOM 1
03-PLATE
04-LARGE STAGE
05-SMALL STAGE
06-VOCAL ECHO
07-KARAOKE 1
08-DELAY 1
09-P.P.DELAY 1
10-TREMOLO
11-CHORUS
12-PHASER
13-FLANGER
14-WAH WAH
15-DOUBLER
16-RADIO
17-DELAY 2
18-DELAY 3
19-DELAY 4
20-DELAY 5
21-P.P.DELAY 2
22-P.P.DELAY 3
23-P.P.DELAY 4
24-P.P.DELAY 5
37-HALL 2
49-ROOM 2
59-DELAY 6
62-KARAOKE 2
65-SOFT CHORUS
69-WARM CHORUS
73-DEEP FLANGER
75-HEAVY FLANGER
79-CHASSIC PHASER
81-REVERS
83-REVERS
85-REVERS
87-PITCH+REVERS
91-DELAY+REVERS
93-DELAY+CHORUS
95-DELAY+FLANGER
97-DELAY+PHASER
99-DELAY+PITCH
PROGRAM
(PUSH)
REPEAT
RECORD BLUETOOTH
USB
24-BIT A
/
D&D
/
A CONVERTER
24-BIT DUAL ENGINE DSP
U-DISK MP3
POWER
+48V
CLIP
0 2
2
4
4
7
7
10
10
20
30
L
R
USB
R EC
MP3
B
D
F
C
A
E
10
11
