better homes BH15-084-899-09 Manual Download Page 23

Stock # BH15-084-899-09 

Please call for replacement parts or assistance: 

1-866-942-5362 

Whalen Furniture Manufacturing 

 

 

 

Page 23    

 

 

     Factory No. 17052 

Care and Maintenance 

 

 

Use a soft, clean cloth that will not scratch the surface when dusting. 

 

Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an 
inconspicuous area. 

 

Using solvents of any kind on your furniture may damage the finish. 

 

Never use water to clean your furniture as it may cause damage to the finish. 

 

Always use coasters under beverage glasses and flowerpots. 

 

Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid 
rubbing. 

 

Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may 
create spotting within the furniture finish. 

 

Stains or marks from crayons or ink markers will be difficult to remove. 

 

In the event that your furniture is stained or otherwise damaged during use, we recommend that 
you call a professional to repair your furniture. 

 

Check bolts/screws periodically and tighten them if necessary. 

 
 
 
 

Further advice about wood furniture care 

 

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and 
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep 
furniture away from direct sunlight as sun may damage the finish. 

 

Proper care and cleaning at home will extend the life of your purchase. Following these important and 
helpful tips will enhance your furniture as it ages. 
 
 
 
 

Cleaning trim for fireplace 

 
Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and buff with a 
clean soft cloth. DO NOT use brass polish or household cleaners as these products will damage the 
metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores. 

 

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during 
assembly or shipping. 

 

We hope you enjoy your purchase for many years. 

Thank you for your purchase! 

Summary of Contents for BH15-084-899-09

























Reviews: