background image

 16

WARNING

: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in  

 

      collapse and possible injury.

Your complete satisfaction is our number 1 priority.  Our product is designed and manufactured to meet the 

highest quality of standards.  In the event that you have assembly questions, or parts are missing or damaged, 

our customer service department would appreciate the opportunity to assist you. 

This product carries a one (1) year warranty against defects in workmanship and materials. Defective product 

will be replaced free of charge within the stated warranty period, when returned by the original purchaser with 

proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please 

contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty 

gives you specific legal rights and you may also have other rights which vary from State to State.

Furniture Care Instructions:  

Dust with clean, lint-free cloth.  

Use furniture spray polish as needed. 

Customer Service:

877.436.7290

[email protected]

For use with televisions weighing 

65 pounds (29.5 kg) or less.  Use with 

heavier televisions may result in 

instability causing tip over resulting 

in death or serious injury.

Use of anti-tip restraints may only 

reduce, but not eliminate, the risk 

of tip-over.

 !

  WARNING

90 lbs

. gener

al use /

65 lbs

. television use

35 lbs

.

25 lbs

.

25 lbs

.

35 lbs

.

!

WARNING

Serious or fatal crushing injuries can occur

from furniture tip-over. To help prevent 

tip-over:

• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top

  of this product, unless the product is 

  specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
  doors, or shelves.
• Never open more than one drawer at a time.

(OR)

• Do not defeat or remove the drawer interlock 
  system.

Use of tip-over restraints may only reduce,

but not eliminate, the risk of tip-over.

This is a permanent label. Do not remove.

Summary of Contents for KENDARA MEDIA CREDENZA BH18-021-199-14

































Reviews: