Better Homes and Gardens BH17-084-098-47 Manual Download Page 22

 

22

 

Care and Maintenance 

 

 

Use a soft, clean cloth that will not scratch the surface when dusting. 

 

Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. 

 

Using solvents of any kind on your furniture may damage your furniture’s finish. 

 

Never use water to clean your furniture as it may cause damage to the finish. 

 

Always use coasters under beverage glasses and flowerpots. 

 

Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing. 

 

Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create 
spotting within the furniture finish. 

 

Stains or marks from crayons or ink markers will be difficult to remove. 

 

In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a 
professional to repair your furniture. 

 

Check bolts/screws periodically and tighten them if necessary. 

 
 
 

 

Further Advice about Wood Furniture Care 

 

It  is  best  to  keep  your  furniture  in  a  climate-controlled  environment.  Extreme  temperature  and  humidity 
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from 
direct sunlight as sun may damage the finish. 

 

Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful 
tips will enhance your furniture as it ages. 

 

A  touch-up  pen  has  been  provided  to  repair  any  small  nicks  or  scratches  that  may  occur  during 
assembly or shipping. 

 

We hope you enjoy your purchase for many years. 

Thank you for your purchase! 

 
 
 

 

QUALITY GUARANTEE 

 

We are confident that you will be delighted with your Whalen Furniture purchase. 

 

Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace 
it  for  up  to  one  (1)  year  from  date  of  purchase.  Every  Whalen  Furniture  product  is  designed  to  meet  your 
highest expectations. We guarantee that you will immediately see the value of our fine furniture. 

 

This warranty gives you specific legal rights and you may also have other rights which vary from State to State. 

 

Customer Service: 866-942-5362 

 

8:30 a.m. - 4:30 p.m., PST, Monday to Friday 

www.whalenstyle.com 

Summary of Contents for BH17-084-098-47













































Reviews: