ROCKER PLATE
ROCKER
ASSEMBLY
H
"U" BAR
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Fig. 1
FOOT CAP
L
M
N
D
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Fig. 2
Fig. 3
Fig. 4
NOTE: MAKE SURE ARROWS
FROM BOTH THE "U" BAR
AND ROCKER ASSEMBLY
ARE POINTING IN THE
SAME DIRECTION!
SEAT DESIGNS MAY
VARY BUT THE ASSEMBLY
IS THE SAME
Step 1:
Do not attempt assembly if any parts are missing or damaged.
Step 2:
Fig 1
Hand tighten only
Step 4:
Do not over tighten. Over tightening may strip bolts.
Step 5:
See Fig.2
Step 6: Critical Step: The "U" metal plates must be installed in the proper location.
Fig.3
Fig.4 Hand tighten nuts 3-4 revolutions only.
CAUTION: Failure to place "U" metal plates under the rocker plates and above the "U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the structure of the rocker
plates and the "U" bar. Damage due to over tightening of bolts or improper assembly could cause injury and may void your warranty.
Step 7:
Do not over tighten.
Step 8:
.
,
Identify all parts packed in the carton against the parts list. Remove all protective materials. Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are unsure how to proceed with the assembly, call
our Customer Service Center at 1-800-416-3511.
Attach the right arm to the chair frame by using a 1/4"x15mm bolt and a 1/4"x55mm bolt as shown in
. Guide the bolts through the holes in the right arm into pre-drilled holes in the chair frame.
. Repeat for the
left arm.
At this time make any adjustments to alignment of all parts. Tighten all bolts a few revolutions at a time, alternating between bolts until tightened.
Note the arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the rocker plate. Point the open end of the horseshoe away from you. The arrows on the rocker assembly should be pointing towards you.
Set the chair frame on the rocker assembly with front of the seat facing you and the arrows on the "U" bar pointing towards you (
). This is very important for a safe, balanced rocking motion. If chair frame has been
properly positioned on the rocker assembly, all arrows on the "U" bar and rocker assembly will be pointing in the same direction.
Insert the "U" metal plate, so that the "U" bar and rocker plate are between both sides of the "U" metal plate. Make
sure that the holes in the "U" metal plate are completely aligned with the holes in the "U" bar as shown in
. Guide the bolts through the holes on the top side of the "U" metal plate, through the holes in the "U" bar portion of the
chair, through the holes in the rocker plate and then, most importantly, through the holes in the bottom side of the "U" metal plate. It is very important that the holes in the bottom portion of the "U" metal plate be placed directly beneath
the holes in the rocker plate. Add a spring washer and a nut to each bolt as shown in
.
Repeat the same procedure on the other side.
Tighten all nuts and bolts with the hex wrenches provided.
Remove arrow labels from "U" bar and rocker assembly. Cover all bolts with bolt covers.
Your chair is ready for use. If you need any assistance, please call our Customer Service Center at 1-800-416-3511.
Read this step and carefully examine.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty. Please read all instructions carefully before assembly. If you have any questions
regarding your assembly, call our Customer Service Center at 1-800-416-3511.
Page 2
O
"U" BAR
E
E
F
G
B
C
D
A
P
