BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 29

Page: 29 / 134

Unpacking and Installation

Manual No. 101300

Unpacking and Installation

3-11

March 16, 2015

Operating Instructions and Parts List for the Whizard Quantum

Trimmer

ATTACHING WHIZARD QUANTUM

TRIMMER TO THE WHIZARD

QUANTUM

DRIVELINE

Non-Disconnect Models

•

Hold Whizard Quantum

Trimmer in the hand you will use in operation.

•

With opposite hand, grasp the Whizard Quantum

Driveline and push it through handle

retaining knob.

•

Push driveline until both detents on casing latch collar are inserted. Two clicks (2) will be
heard.

COMPANY

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands