Beta Motorcycles RR 125 2018 Owner'S Manual Download Page 87

Page: 87 / 88

TROUBLESHOOTING

PROBLEM

CAUSE

REMEDY

Engine does not start -Fuel system clogged (fuel lines, fuel

tank, fuel cock)

Contact authorised BETAMOTOR
customer service

- Air ﬁlter dirty

Check the air ﬁlter

- No current supplied to spark plug

Clean or replace the spark plug. If the
problem persists, contact authorised
BETAMOTOR customer service

- Engine ﬂooded

Operate the electrical starter push
button 2 times for 5 seconds. If the
vehicle does not start, remove and dry
the spark plug

- Excessive distance between the electrodes Check the distance between the electrodes
- Ignition connector or coil slackened or oxidized Clean with a spray product for electric contacts and tighten
- Presence of water in the carburettor

Empty the carburettor tank

The engine starts but
the telltale “MIL” lights
on

- Engine management system fault

Contact authorised BETAMOTOR
customer service

“High Voltage” appe-
ars on the instrument

- Overcharging

Turn off the engine and contact author-
ised BETAMOTOR customer service

Engine misﬁres

- Spark gap wrongly adjusted

Restore the spark gap

- Spark plug dirty

Clean or replace the spark plug

The engine does not
hold idling

- Idling air jet clogged

Contact authorised BETAMOTOR
customer service

- Adjustment screws poorly adjusted

Adjust

- Faulty spark plug

Replace the spark plug

- Faulty ignition system

Check the coil and the spark plug cap

Engine overheats and
loses power

- Silencer partly clogged

Contact authorised BETAMOTOR
customer service

- Laminar pack damaged

Contact authorised BETAMOTOR
customer service

- Fault in the ignition system

Contact authorised BETAMOTOR
customer service

Excessive smoke

- Possible mixer system fault

Contact authorised BETAMOTOR
customer service

Front braking poor

- Brake pads worn

Contact authorised BETAMOTOR
customer service

- Air or humidity in the hydraulic circuit Follow the procedure described on

page 59

Rear braking poor

- Brake pads worn

Contact authorised BETAMOTOR
customer service

- Air or humidity in the hydraulic circuit

Follow the procedure described on

page 62

Summary of Contents for RR 125 2018

























































































Search results

Summary of Contents for RR 125 2018

Reviews:

Brands by name

Popular brands

Beta Motorcycles RR 125 2018, Owner'S Manual

Search results

Summary of Contents for RR 125 2018

Reviews:

Brands by name

Popular brands