3
SETUP
USING THE CHLORINATOR
CHECK LIST
To check the parts inside the manual. Verify that the equipment components represent the model that you had intended to purchase. In case of any
damaged or missing parts at the time of purchase, visit our website bestwaycorp.com/support. Drawings are for illustration purposes only. May not
reflect actual product. Not to scale.
PRODUCT SPECIFICATIONS
RECOMMENDATIONS BEFORE INSTALLATION
• The chlorinator must be installed at the last position of the water circulation pipe (down the direction of the water flow) as shown in "1a. and 1b.".
• Only use sodium chloride (NaCl) salt with a purity of at least 99.8% to fully dissolve it.
• Too low salt content will reduce the efficiency of the chlorinator and result in low chlorine production. High salt content may produce a salty taste
to the pool water and it may cause corrosion to metal fixtures and fittings in the pool.
• The "Pool Salt Table" shows the correct amount of salt required. Refer to the different quantity of water. The salt in the pool will not automatically
decrease.
• Only when the pool water is lost will the salt in the water decrease, and the evaporation of water will not cause the salt to decrease.
If the device shows error E2, it is necessary to reduce the salt concentration: Drain about 20% of the pool water, and then refill with clean water.
Wait 1 hour, and if the error still remains, repeat the operation until the E2 error disappears.
In case the quantity of water of your pool is not listed in the “pool salt table”, follow the below formula to calculate the correct quantity of salt to add
to the pool to reach the 3000 ppm of salt concentration, or in case the E1 error appears on the display.
Maximum chlorine production per hour:
Sand filter/Filter pump flow range:
Salt concentration:
Water temperature:
Ambient temperature:
Compatible with max water capacity:
6 g/h
330-3000 gal/h
3000 ppm (3 g/L
）
10-36°C
5-45°C
7000 gal (26495 L)
Press and hold for 3s to turn on/off the chlorinator
Press and hold for 3s to lock/unlock, and press quickly
to adjust working time
When the lock indicator is unlit, the product is unlocked. If
no button is pressed, the product will automatically lock
after 1 minute and the Lock indicator will turn red.
Red: The salt concentration is too high, part of the salt
should be removed from the pool water. Display shows: E2;
Green: The salt concentration is at the optimal level;
Yellow: The salt concentration is too low and salt needs to
be added to the pool water. Display shows: E1.
Shows red, no water flow or insufficient water flow
Displays running time/remaining time/fault code
Power-on state/standby mode
Code
number
Icon
Name
Power button
Timer button
Lock indicator
Salt
concentration
indicator
Water flow
status indicator
Digital Display
Illustrate
1
2
3
4
5
6
(kg)
Water capacity(l)
*0.003
(lb)
Water capacity(gal)
*0.025
The amount of salt added for the first time:
The amount of salt that needs to be added if the "E1"
error code displays:
(lb)
Water capacity(gal)
*0.0084
(kg)
Water capacity(l)
*0.001
Pool capacity
Pool Salt Table
The amount of salt added for the
first time 3.0 g/L (3000 ppm)
Display code "E1" the amount of
salt that needs to be added
(gal)
1000
1500
2000
3000
4000
5000
6000
7000
(l)
3785
5677
7570
11355
15140
18925
22710
26495
(lb)
25
38
50
75
100
125
150
175
(kg)
11
17
23
34
45
57
68
79
(lb)
8
13
17
25
33
42
50
58
(kg)
4
6
8
11
15
19
23
26
