background image

3.

Install a 2x4 block on the opposite side wall and secure the truss.

Step 9

Install Siding on Front Wall

Step 10

Install Roof Gable

Install 2x4 Block

1.

Select a truss with a gusset installed on one side. Position this truss with

the gusset facing towards the inside of the building and flush with 2x4s
on back wall.

2.

Install a 10" to 12" long 2x4 block on a side wall using 10d sinkers.

Secure the truss to the 2x4 block with (2) two 10 sinkers.

3.

Install the 16-1/2" panel

with the 'cut' edge flush
with the door opening.

4.

Install last siding panel.

Cut Edge

Cut Edge

Cut Edge

12-1/2" Siding with 'Tongue' edge

15-3/4" Siding with 'LAP' edge

1.

Select a 12-1/2" siding panel with a 'Tongue' edge and install at the front left corner. Cut edge

will be flush with side wall siding. Install a 15-3/4" siding panel with a 'LAP' edge next. Cut
edge should be flush with door opening.

2.

Install (2) two 4-3/4" x 32-1/4" siding panels over the door opening. Bottom of siding should

extend 3/4" below header. Trim will cover where the siding panels butt together in the center.

Siding 3/4"

Below Header

Summary of Contents for the Elm R

















Reviews: