manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

54733-10BA2L 

1 – 92

02.2017

7 Functional Safety

Volume 1

7.2

Use

The measuring device LB 480 may only be used as intended. Per-
missible measuring arrangements as well as the intended use are 
described in the operating manual.

For use in safety-related systems (Functional safety according to 
IEC 61508:2010 / 61511:2003) all information in this manual has 
to be considered. 

The measuring device can be operated in the operating mode with 
low demand rate (low demand) or with high demand rate (high 
demand). For this purpose, the rules according to 7.4.5.3 of IEC 
61508-2 regarding the demand rate must be observed specifically

•

up to SIL 2 with one detector LB 480

•

up to SIL 3 with two detectors LB 480

Any use beyond the information given in this manual shall be 
deemed as being not in conformity with the intended use and may 
result in serious injury or property damage. BERTHOLD 
TECHNOLOGIES GmbH & Co. KG shall not accept any liability for 
such injury or damage.

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

ParTech 8100 Instruction Manual preview
8100
Brand: ParTech Pages: 14
Hama TH-200 Operating Instruction preview
TH-200
Brand: Hama Pages: 6
Hanna Instruments HI99151 Quick Reference Manual preview
HI99151
Brand: Hanna Instruments Pages: 2
Hanna Instruments HI736 Instruction Manual preview
HI736
Brand: Hanna Instruments Pages: 2
Hanna Instruments HI 991401 Instruction Manual preview
HI 991401
Brand: Hanna Instruments Pages: 2
Hanna Instruments HI 98140 Manual preview
HI 98140
Brand: Hanna Instruments Pages: 4
Hanna Instruments HI 8314 Instruction Manual preview
HI 8314
Brand: Hanna Instruments Pages: 2
X-Rite DensiEye 100 Reference Manual preview
DensiEye 100
Brand: X-Rite Pages: 50
CA.MI T-PLUS User Manual preview
T-PLUS
Brand: CA.MI Pages: 68
JENCO EC3840 Operation Manual preview
EC3840
Brand: JENCO Pages: 13
Palstar ZM-30 Operating Manual preview
ZM-30
Brand: Palstar Pages: 15
Keller dv-2 Operating Manual preview
dv-2
Brand: Keller Pages: 4
Vanguard Instruments Company TRF-100 User Manual preview
TRF-100
Brand: Vanguard Instruments Company Pages: 111
LaserLiner DistanceMaster Compact Operating Instructions Manual preview
DistanceMaster Compact
Brand: LaserLiner Pages: 14
inbody 370S User Manual preview
370S
Brand: inbody Pages: 36
Pilot Communications PMAC615 Installation & Operation Manual preview
PMAC615
Brand: Pilot Communications Pages: 34
CODEL Energy Tech 401 Installation, Operation And Maintenance Manual preview
Energy Tech 401
Brand: CODEL Pages: 131
iDigit A570 Ambient Monitor Instruction Manual preview
A570 Ambient Monitor
Brand: iDigit Pages: 15

Brands by name

Popular brands

Load more brands