background image

 

3

Requirements

 

1. Overhead clearances (Minimum values) 

The minimum overhead clearances shall be in accordance with the minimum values indicated in the table 
n.1 and are shown and in the fig. 1- 2 
Range  hoods  and  exhaust  fans  shall  be  installed  in  accordance  with  the  manufacturer’s  instructions. 
However, in no case shall the clearance between the top of the highest burner of the cooking appliance and 
the range hood be less than 650mm.  
Any other downward facing combustible surface less than 600mm above the top of the highest burner shall 
be protected for the full width and depth of the cooking surface area. 
However, in no case shall this clearance to any surface be less than 450mm. 
Maximum depth for the overheads cabinet is 330mm 

2. Side clearances (Minimum values)

 

The different side clearances shall be in accordance with the minimum values indicated in the table n.1  and 
are shawn and in the fig. 1- 2 

The cooking surface area is defined as that part of the appliance where cooking normally takes place and 
does not include those parts of the appliance containing control knobs. 

Table n.1   

Hobs  models 

Type A 
Type B 

 

Hobs  

models

Type A 
Type B 

Min. Clearances 

(mm) 

Min. Clearances

(mm) 

L1 

500 

L10

870 

L2 

40 

L11

915 

L3 

50 

W

890 

L4 

457 

D

520 

L5 

600 

B1 (*)

40 

L6 

330 

B2 (*)

152 

L7 

925 

B3 (*)

40 

L8 

40  

B4 (*)

152 

L9 

172 

 

(*) Note: 
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet. 
-B2  and  B4  are  the  min.  clearance  between  the  left/right  side  edge  of  the  appliance  and  the  side  wall  (if 
present). 
-B3 is the min. clearance between the back edge of the appliance and the back wall. 

Attaching the hotplate

 

To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with 
a special gasket. To apply this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing 
strips along the edges of the opening in the bench top and carefully overlap the strip end. (See Fig. 3). insert 
the hotplate into the bench top opening. With a screwdriver assemble the brackets to the hotplate bottom by 
means of the screws . (See Fig. 3A-3B). Slide the hooks into position and secure them with the screws. 
Trim the part of the sealing strips which extend beyond the hotplate base 

 

IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE 

The hob can be installed by  itself, in an isolated position or inserted between two kitchen units or 
between  one  kitchen  unit  and  a  wall.  Furthermore  the  back  wall  and  surrounding  surfaces  must 
resist a temperature of 65 K. 
To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the 
two surfaces together must resist temperatures of up to 150 °C 
The installation of the appliance must be carried out according to the norms in force of the country 
concerned and the appliance must be installed in a well ventilated place.  

Summary of Contents for PM36500X













Reviews: