background image

8

INSTALLATION

FIG. 9

4) FIXING THE HOT PLATE

The  hot  plate  has  a  special  seal  which  prevents
liquid  from  infiltrating  into  the  cabinet.  Strictly
comply  with  the  following  instructions  in  order  to
correctly apply this seal:
-  take off all the movable parts of the hob.
- Cut the seal in 4 parts of the necessary lenght to

positionning it on the 4 edges of the crystal.

- Overturn the hot plate and correctly position seal

“E” (fig. 9) under the edge of the hot plate itself,
so  that  the  outer  side  of  the  seal  perfectly
matches the outer perimetral edge of the crystal.
The  ends  of  the  strips  must  fit  together  without
overlapping.

- Evenly  and  securely  fix  the  seal  to  the  crystal,

pressing it in place with the fingers.

-  Insert  the  hooks  into  their  relative  housings  and

fix them to the body using screws “G” (fig. 10).

-  Fix  the  appliance  in  the  hole  made  on  the

furniture and lock it with the proper screws “F” of
the  fixing  hooks  “G”  (look  at  fig.  10/A).  Use  a
hand screwdriver and exert only moderate force.

-  In  order  to  avoid  accidental  touch  with  the

overheating  bottom  of  the  hob,  during  the
working,  is  necessary  to  put  a  wooden  insert,
fixed  by  screws,  at  a  minimum  distance  of  70
mm from the top (see fig. 7).

FIG. 10/A

FIG. 10

Summary of Contents for P7C01G9XT

















Reviews: