![Berner BACS 14,4V LI Operating Instructions Manual Download Page 24](http://html1.mh-extra.com/html/berner/bacs-14-4v-li/bacs-14-4v-li_operating-instructions-manual_2738064024.webp)
English
23
CAUTION:
The selection examples shown in Table 5 should be
considered as general standard. As different types of
tightening screws and different materials to be
tightened are used in actual works proper adjustments
are naturally necessary.
When using the driver drill with a machine screw at
HIGH (high speed), a screw may damage or a bit may
loose due to the tightning torque is too strong. Use
the driver drill at LOW (low speed) when using a
machine screw.
NOTE:
The use of the battery BAC-LI in a cold condition
(below 0 degree Centigrade) can sometimes result in
the weakened tightening torque and reduced amount
of work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
6. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION:
When using the hook, hang up the power tool firmly
not to drop accidentally.
If the power tool is dropped, it may lead to an accident.
When carrying the power tool with hooked to your
waist belt, do not fit any bit to the tip of power tool. If
the sharp bit such as drill is fitted to the power tool
when carrying it with hooked to your waist belt, you
will be injured.
Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
(1) Removing the hook.
Remove the screws fixing the hook with Philips screw
driver. (Fig. 9)
(2) Replacing the hook and tightening the screws.
Install securely the hook in the groove of power tool
and tighten the screws to fix the hook firmly. (Fig. 10)
7. About Remaining Battery Indicator
When pressing the remaining battery indicator switch,
the remaining battery indicator lamp lights and the
battery remaining power can be checked. (Fig.11)
When releasing your finger from the remaining
battery indicator switch, the remaining battery
indicator lamp goes off. The table 6 shows the state
of remaining battery indicator lamp and the battery
remaining power.
Use
Clutch Position
Rotating speed selection (Position of the shift knob)
LOW (Low speed)
HIGH (High speed)
Machine
1 – 22
For 6 mm or smaller diameter
For 4 mm or smaller
Driving
screw
screws.
diameter screws.
Wood screw
1 –
For 6.8 mm or smaller nominal
For 3.8 mm or smaller
diameter screws.
nominal diameter screws.
Wood
For 36 mm or smaller
For 18 mm or smaller
Drilling
diameters.
diameters.
Metal
For drilling with a metal
–––––––––––––––
working drill bit.
5. How to select tightening torque and rotational speed
Table 5
When setting the shift knob to “HIGH” (high speed)
and the position of the clutch dial is “17” or “22”, it
may happen that the clutch is not engaged and that
the motor is locked. In such a case, please set the
shift knob to “LOW” (low speed).
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor or
battery may be burnt.
Be sure to turn the shift knob.
Work
Suggestions
Wood
Drilling
Steel
Use for drilling purpose.
Aluminum
Machine screw
Use the end piece or soc ket matching the screw diameter.
Driving
Wood screw
Use after drilling a hole.
Table 4
4. The scope and suggestions for uses
The usable scope for various types of work based on
the mechanical structure of this unit is shown in
Table 4.
Summary of Contents for BACS 14,4V LI
