15
ENGLISH
EC-Declaration of Conformity
Machinery Directive
SDS Max Combination & Chipping
Hammer
BHD-6-45
BERNER
declares that these products described under
Technical
Data
are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-6:2010.
Level of sound power according to 2000/14/EC (Article 12,
Annex III, No. 10; m </= 15 kg)
L
WA
(measured sound power level)
dB
101
L
WA
(guaranteed sound power level)
dB
103
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact
BERNER
at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of
BERNER
.
i.V. Bert Habets
Senior Director Continuous Improvements
Berner Trading Holding GmbH
Bernerstraße 6, 74653 Künzelsau, Germany,
01.04.2018
WARNING:
To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER:
Indicates an imminently hazardous
situation which, if not avoided,
will
result in
death
or serious injury
.
WARNING:
Indicates a potentially hazardous
situation which, if not avoided,
could
result in
death
or serious injury
.
CAUTION:
Indicates a potentially hazardous
situation which, if not avoided,
may
result in
minor
or moderate injury
.
NOTICE:
Indicates a practice
not related
to personal injury
which, if not avoided,
may
result
in
property damage
.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and
all instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a )
Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
b )
Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which
may ignite the dust or fumes.
c )
Keep children and bystanders away while operating
a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a )
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b )
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c )
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk
of electric shock.
d )
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
e )
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f )
If operating a power tool in a damp location
is unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of
electric shock.
Summary of Contents for 342990
