manualshive.com logo in svg

Berlin Heart EXCOR Pediatric VAD, Manual, Page: 206 / 250

Share
Download
Berlin Heart EXCOR Pediatric VAD Manual Download Page 206

Chapter 15  Troubleshooting and correcting faults 

INSTRUCTION 

1.

  

Bring membrane to the end-of-diastole position, position de-airing needle, 
rinse and fill pump with sterile injectable saline (see section 8.4: Moving the 
membrane to the end-of-diastole position, page 112 and section 8.5: De-airing 
the blood pump, page 112). 

2.

  

Connect the driving tube to the respective driving tube connector of the pump. 

3.

  

Place the pump, ready for connection, with the titanium connectors pointing 
upwards. 

15.1.2  Replacing the right blood pump (RVAD/ BVAD) 

Material 

•

  

1 prepared replacement blood pump (see section 15.1.1: Preparing a 
replacement blood pump, page 195) 

•

  

1 tube connecting set (cable tie, cable-tie gun), included in the accessory set. 
Only the cable ties and cable tie guns provided should be used. 

Stopping the right blood pump and detaching the blood pump from Ikus 

INSTRUCTION 

1.

  

Bring the patient into the Trendelenburg position. 

2.

  

The cable tie covering the EXCOR cannula on the stub of the blood pump 
should be removed carefully. Use an appropriate blunt tool. 
Important: never use a sharp instrument, for example, a scalpel or scissors, to 
remove the cable tie. This may cause damage to the cannula. Check cannulae 
immediately to make sure they are not damaged. 

3.

  

If necessary log into the monitor program by entering user ID and password, 
confirming the password with 

<Enter>

. 

4.

  

BVAD: Reduce rate of left blood pump to 30 bpm. Use 

<

←

>

/ 

<

→

>

 to navigate 

cursor to the respective field of the parameter table, then use 

<

↓

>

 to adapt 

value. Confirm with 

<Enter>

. 

5.

  

In the monitor program, select the option 

Pause left

 respectively 

Pause right 

and press 

<Enter>

 to confirm. Respond to the prompt in the dialog window by 

pressing the 

<X>

 key or the 

<1>

 key. The right blood pump will stop. 

RVAD: 

Pause left 

BVAD: 

Pause right 

The view 

Pump size and single-step mode

 is displayed. 

6.

  

As soon as the right pump has stopped, clamp off the cannulae beneath the 
right pump to be replaced and slide the cannulae off the pump. If it is neces­
sary to clamp any other part of the cannula that is not covered with velour, 
cover the part of the cannula that will be clamped with a gauze sponge. 

7.

  

Check cannulae for visible deposits. If necessary, remove these deposits care­
fully. 

8.

  

Remove the driving tube of the pump to be replaced from the connector. To do 
so, take hold of the release sleeve and pull this out of the connector. 

1000721x09 Revision 8 

196 

Summary of Contents for EXCOR Pediatric VAD



























































































































































































































































Reviews:

No comments