background image

Page 7

12. The headshell on Magne tonearm is complete parallel to the sliding pipe, such as the cartridge azimuth is

perfect when mounted on the headshell.

Note:

If adjustment is required, it must be done by using spacers between cartridge and head shell.

13. Turn on the airsupply.

The 2 screws on the tonearm base is also for leveling the tonearm.

Depending on how much the left or the right screw is tighten, the tonearm airpipe can be tilted to the left

or to the right.

Ex:

Tilt to the left by slightly untighten the right screw- tighten the left screw, and visa versa.

Pic. 14.

11. Turn the cartridge such as the stylus is parallel to the alignment tools`crossline, Pic. 14. Tighten the cartridge

( If the cartridge has a flat front, you can use any non magnetic device, Pic. 15.)

Untighten the 2 screws on the armbase, and move the tonearm forward or backward to adjust the overhang,

Pic. 16.

Move the tonearm, so the styles tip is exactly in the groove of the alignment tool, Pic. 17.

Pic. 15.

Pic. 16.

cross line

Pic. 17.

Pic. 18.

adjustment pipe

The adjustment pipe is a helpfull tool to ease the level of the airpipe, which is vital for a linear tracking

airbearing tonearm.

Draw the adjustment pipe onto the airpipe, Pic 18. Make sure the adjustment pipe is sliding frictionless on

the airpipe. Adjust the airflow if necessary.
When the adjustment pipe float and remain on the same point, the level is correct.

Summary of Contents for Magne













Reviews: