BERGHOF ET2115 User Handbook Manual Download Page 15 | Manualshive

Page: 15 / 48

background image

USER HANDBOOK 1.0 | ET2115

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com
21-0099-82-00-00-003 | 222002100_Anwenderhandbuch_Ethernet-Terminal-ET2115_EN.docx

15

Fig. 3: Installation cut-out



Cut a rectangular installation cut-out in the support material:
Height: 260 mm
Width: 402 mm
Max. corner radius: 3.0 mm

Thickness of the support material:
Optimally: 2.0–3.0 mm
Max.: 4.0 mm

«
...
13
14
15
16
17
...
»

Summary of Contents for ET2115

















































Reviews:

No comments

Related manuals for ET2115

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: GE Pages: 425

Brand: Echelon Pages: 40

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Yudian Pages: 26

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Haldex Pages: 8

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Maestra Pages: 22

Brand: NCR Pages: 8

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: Watts Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands