manualshive.com logo in svg

BenQ MW571, User Manual

Share
Download
BenQ MW571 User Manual Download Page 37

Operation

37

Main menu Sub-menu

Options

5. 
SYSTEM 
SETUP: 
Advanced

High Altitude Mode

On/Off

Audio 
Settings

Mute

On/Off

Volume
Power On/Off Ring 
Tone

On/Off

Lamp 
Settings

Lamp Mode

Normal/Economic/SmartEco/
LampSave

Reset Lamp Timer
Lamp Timer

Security 
Settings

Change Password
Change Security 
Settings
Power On Lock

On/Off

Baud Rate

2400/4800/9600/14400/19200/
38400/57600/115200

Test Pattern

On/Off

Closed 
Caption

Closed Caption 
Enable

On/Off

Caption Version

CC1/CC2/CC3/CC4

Standby 
Settings

Network

Enable Network Standby Mode
Auto Disable Network Standby 
Mode

Monitor Out

On/Off

Audio Pass Through

Off/Audio In/HDMI

Network 
Settings

Wired LAN

Status
DHCP
IP Address
Subnet Mask
Default Gateway
DNS Server
Apply

AMX Device 
Discovery

On/Off

MAC Address

Reset All Settings

6. 

INFORMATION

Current System Status

• Source
• Picture Mode
• Lamp Mode
• Resolution
• 3D Format
• Color System
•  Lamp Usage Time
• Firmware Version

Summary of Contents for MW571






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands