Programming
Bennett HF H35 Instruction Manual
52
PROCEDURE - READING THE TOTAL NUMBER OF SALES AND PRICE CHANGES:
1.
Press the [
+/-]
button. The main display indicates Product 1
counter totals.
a.
The top line of the display shows the number of sales for
Product 1. The second line shows the number of price
changes for Product 1.
2.
To read the counters totals for Product 2 press the
[ENTER]
button.
NOTE: To move from money press the UP
↑
button, to mass
press the ↓ button, to counter totals press the +/
-
button.
Remember, only the number of products selected in Menu
Code 7 will be displayed.
CAUTION: THE FOLLOWING PROCEDURE ZEROS ALL THE SHIFT
MONEY, MASS, AND COUNTER TOTALS IN THIS MENU CODE.
MAKE SURE ALL TOTALS ARE RECORDED BEFORE PROCEEDING
WITH THE NEXT STEP. DATA CANNOT BE RETRIEVED.
3.
To reset the totals, press the
0
button. The screen will flash with
the message as shown in
4.
Press [
ENTER
] and the display returns to P11.d. ALL TOTALS IN
MENU CODE 26 ARE RETURNED TO ZERO.
5.
Press the [
CANCEL
] button to exit this menu.
Figure 4.40
–
Counter Totals
Figure 4.41
–
Totals Reset
MENU CODE 27
–
HOW TO PERFORM AN ELECTRONIC CALIBRATION
Menu Code 27 allows the technician to perform an electronic calibration procedure. In an overwrite calibration procedure, the
new entered value replaces the existing value.
WARNING: YOU MUST PERFORM THE E-CAL PRIOR TO DISPENSING FUEL. IF THE E-CAL IS NOT PERFORMED
PROPERLY, THE DISPENSER WILL PRODUCE A CALIBRATION ERROR.
Currently this switch is in Normal Operating Mode. Prior to entering E-Cal Mode, you must
slide the switch to the right on the CPU Board to gain access. If you attempt to dispense with
this switch in E-Cal Mode, the dispenser will give you an
Error 74
section for the list of error codes.
Figure 4.42
–
E-CAL Switch
DIRECT PERCENTAGE ENTRY
Prior to performing any E-Cal procedure go to Mode 6 and make sure, the dispenser configuration is correct. Also, make sure that
every product has a price other than zero. A zero price will prevent the use of any configured meter. The direct percentage entry
procedure provides a way of zeroing or overwriting the electronic calibration correction constant.
Sale $
E N t E r
Kilograms
r E s E t s
Switch
Summary of Contents for HIGH FLOW H35
