Programming
Bennett HF H35 Instruction Manual
37
MENU CODE 2 - READING ELECTRO -MECHANICAL TOTALS
Menu Code 2 allows the operator and/or manager read the Electronic Mechanical Totals. If the operator or manager did not
enter a different value in Menu Code 5, this total should be the same as the dispenser electro-mechanical totalizers.
PROCEDURE
1.
Press the
2
button and then the [
MODE
] button on the
keypad.
a.
The main display shows the electro-mechanical
total.
b.
The total number is carried to three decimal places.
c.
The PPM display reads
T1.2
for Product 1 Electro-
Mechanical Totalizer, Menu Code 2.
2.
To read the totals for the remaining meters, press the
[
ENTER
] button.
Note:
See
How to Read Electronic Totals
with a Magnetic Reed Switch
for instructions on reading
Menu Code 2 totals.
Figure 4.7 - Product 2 Electro-Mechanical Total
MENU CODE 3 -
MANAGER’S ACCESS CODE ENTRY
NOTE: Manager’s Mode access is canceled when the Manager’s Keypad is unplugged from the dispenser. If the
Manager’s Keypad i
s removed, you must re-
enter the Menu Code 3 manager’s access code to regain programming
access.
Access to Menu Codes 4 through 99 is gained by entering a four-digit access code. The software is set with an access code at the
factory of
2218
. All dispensers covered in this manual are shipped with this code. Menu Code 3 must be used each time the
manager wishes to access or program Menu Codes 4 through 99.
HOW TO ACCESS THE MENU CO DE
1.
Press the
3
button and then the
[MODE
] button on the Manager’s
Keypad.
2.
Enter the default number
2218
. Four dashes appear in the display.
3.
Press the [
ENTER
] button. When access is gained, the dashes
disappear, and the price display appears. If the dashes do not appear,
the access code entered did not match the code stored in memory.
Press the [
CANCEL
] button and repeat steps 1, 2, and 3.
4.
When access is gained, press the [
CANCEL
] button to exit. It is
necessary to exit Menu Code 3 before the remaining protected menus
can be accessed. The display shown in
appears when the
cancel button is pressed.
Figure 4.8
–
Access code entry
Figure 4.9 - Menu code exit
Sale $
C O d E
Kilograms
0 0
S i d E 1
- - 1
Sale $
p A s s
Kilograms
----
C O d E
- - 3
Summary of Contents for HIGH FLOW H35
