6. MAINTAINING YOUR COMPRESSOR
IMPORTANT
: Before doing any maintenance on your compressor make sure the unit is not pressurized by opening the release valve and
disconnect from any source of power.
•
Use only a dampened cloth to clean exterior of compressor.
•
Avoid using any detergent or solvents, which might contain chemical that could damage plastic components and/or painted
surfaces of the compressor.
•
All other services should be performed by an Authorized Service Personnel.
A. Cotton Filter
It is recommended that you change the cotton air filter after the earlier of three (3) months, 50 hours of use or if they become deformed or
extremely dirty (filters sold separately).
IMPORTANT
: Before using and/or storing the compressor, inspect its cotton filter in the oil/water separator as follows:
1.
Remove the filter housing from the top of the compressor.
2.
Using snap ring pliers, unscrew the brass filter cover and remove the cotton filter.
3.
Squeeze the cotton filter dry to remove excessive amount of moisture.
4.
Replace cotton filters if it become deformed or extremely dirty (filter sold separately).
B. Lubricating the compressor
This compressor is lubricated using solid lubricants. MP-3 or Multipurpose Lithium grease is the
recommended solid lubricant. It is recommended that you do this once a year.
1.
Remove the cover from the compressor.
2.
Locate the two lubrication port on the right side of the compressor (Fig. 8).
3.
Remove rubber plugs and add 1oz of MP-3 grease to each lubrication port.
4.
Re-install rubber plugs into housing and the cover on the compressor.
7. EXPLODED VIEW OF PARTS
Cleaning or replacing these parts can solve most of the compression problems. Spare parts, included with the compressor.
1
6
5
9
12
5
2
7
10
3
3
4
8
5
5
11
5
1.
Black Plastic Ball
2.
Black O-Ring (D46*2)
3.
Green O-Ring (D12*2)
4.
Low Pressure Check Valve
5.
White Spacer
6.
Middle Pressure Check-Valve Set
7.
High Pressure Check Valve
8.
Green O-Ring(D14*2)
9.
Green O-Ring (D16*2)
10.
Cotton Filter
11.
POM Black Spacer
12.
Copper Burst Disc
7
8
9
10
11
12
1
4
2
3
5
6
8. LOAD INDICATOR ERROR CODES
A. Issue – L
1. Resolution –
The supply voltage is lower than 10.8v.
B. Issue – H1
1. Resolution –
The supply voltage is higher than 14V.
C. Issue – H2
1. Resolution –
The current is higher than 29 when the machine is working.
D. Issue – H3
1. Resolution –
The temperature is above 85 when the machine is working.
9. TROUBLESHOOTING
A. Issue – Air Compressor will not start
1. Resolution –
Check to make sure the air compressor is plugged into an active electrical outlet or charged 12V battery.
2. Resolution –
Check to make sure the DC AC toggle switch is set on the proper setting for which you plan to power the compressor.
3. Resolution –
Check to see if the fuse failed.
B. Issue – Air Compressor is not building pressure
1. Resolution –
Make sure both release valve and moisture release valve is closed. It should be hand tightened.
2. Resolution –
Check any noticeable air leaks around the fill hose and or fill adapters.
3. Resolution –
Check to see if the burst disk failed.
C. Issue – Air Compressor shuts off before reaching desired pressure
1. Resolution –
Make sure the Output Pressure (Auto Shut Off) is set properly.
2. Resolution –
Make sure the converter is switched to the right output voltage of the plug.
D. Issue – Burst Disc Failure
1. Resolution –
Should the Burst Disc (Safety Valve) fail during use of the compressor, shut off the compressor. Open the Release
Valve (Bleed Screw) to vent the remaining air from the compressor. Remove the Burst Disc retention screw to verify the Burst Disc
has failed (there will be a hole in it). Remove the failed Burst Disc from the compressor. Additional Burst Discs are in the bag of spare
parts that comes with the compressor. Install a new Burst Disc and re-insert the Burst Disc retention screw by turning it clockwise.
SPECIFICATIONS
Working Voltage
Direct Current 12V-15V
Motor Power
DC12V 350W or AC 110V or 220V 450W
Working Pressure
Up to 4,500 PSI
Application Range
Airgun/Paintball Cylinders less than .6L (600cc)
LIMITED ONE YEAR WARRANTY
This product is warranted to be free of defects in materials and workmanship for 1 year. Buyer should retain the original sales receipt as
record of date of purchase. This warranty does not cover adaptors, filters, attachments or other accessories. In the event of a defect under this
warranty, Crosman will, at its option, repair or replace the product; provided, however, its inspection indicates that an original defect exists.
Crosman reserves the right to replace any product which is no longer available with a product of comparable value and function. If Crosman
determines the repair is not covered under the warranty guidelines, there could be a charge to you for the repair.
WHAT IS COVERED
1.
Parts and Repair of any factory defect of material or workmanship.
2.
Transportation charges to consumer for the repaired product and/or replacement product.
WHAT IS NOT COVERED
1.
Transportation charges to the Authorized Service Personnel for defective product.
2.
Normal wear and tear from regular use.
3.
Damaged parts as a result from misuse, neglect or tampering.
4.
Damage caused by abuse, modification or failure to perform normal maintenance – see Owner’s Manual.
5.
Improper installation or maintenance performed by someone other than an Authorized service personnel.
6.
Any other expense.
THIS LIMITED WARRANTY DOES NOT INCLUDE CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES OR INCIDENTAL EXPENSES, INCLUDING
DAMAGE TO PROPERTY OR ANY OTHER EXPENSE. CROSMAN DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR ALLOW LIMITATIONS ON IMPLIED WARRANTIES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. TO THE EXTENT ANY
PROVISION OF THIS WARRANTY IS PROHIBITED BY FEDERAL, STATE OR MUNICIPAL LAW, IT SHALL NOT BE APPLICABLE. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.
STOP – BEFORE YOU RETURN THIS PRODUCT TO THE STORE
Save on gas and avoid the trip back to the store. Contact our Customer Service/Technical Support representatives for information and
trouble-shooting help. Call 1-800-7AIRGUN (1-800-724-7486) or find answers to frequently asked questions at www.crosman.com.
WARRANTY CLAIM AND REPAIR SERVICE
If your compressor needs repair - DO NOT ATTEMPT TO DISASSEMBLE IT! Your compressor requires special tools and fixtures to repair it. Any
disassembly or modification not performed by Authorized Service Personnel will void the warranty.
U.S. Customers -
Contact Crosman Customer Service at 800-724-7486 or e-mail us via www.crosman.com. You will be instructed where and
how to send your compressor in for repair under warranty.
Crosman Corporation
Attn: Warranty Dept.
7629 Route 5 & 20
Bloomfield, NY 14469
Include with your product a copy of your receipt and a brief description of the problem. Be sure to indicate your name, mailing address, e-mail
address and telephone number. We recommend you use a method of shipping that provides you with a tracking number and insurance
options. Crosman is not liable for any damaged, lost or stolen merchandise during shipping.
Canadian Customers -
Contact the Gravel Agency, in Quebec at 866-662-4869.
Outside U.S. Customers -
Please contact your point of purchase dealer/distributor. If you do not know your dealer/distributor, contact our
International Dept. for assistance at 585-657-6161 or e-mail us via www.crosman.com.
Crosman, Traveler and Benjamin are trademarks of Crosman Corporation.
© 2021 Crosman Corporation
06-21 OM
Fig. 8
Fig. 8
