manualshive.com logo in svg

Benelli BJ250-18, User Manual, Page: 25 / 51

Share
Download
Benelli BJ250-18 User Manual Download Page 25

BJ250-18

25

    Slow down the motorcycle when turning to the low gear. Revving up the engine slightly to shift gears in more smooth 
way to avoid damaging gears

TOOL BAG

    The tool bag is in the seat cushion. By using tools in the bag, you can do basic repair and adjustment and change some 
parts when needed.

NOTICE OF USE OF FUEL AND ENGINE OIL

    Fuel
    It is a must to use lead free gasoline. Use gasoline contains octane number more than 92.
    Notice

：

 Use lead free gasoline can extend the working life of spark plug. 

    Engine Oil
    Please use four-stroke engine oil it should be equal or higher than API SAE service grade SF. 
The specification is SJ10W/50.

NOTICE OF USE OF FUEL AND ENGINE OIL

Type

Full synthetic oil

SJ10W-50 or SN 15W-50

Capacity

1.4L±0.1L

Caution:

When the transmission is on neutral position, the indicator lamp would turn on. Slowly release the clutch lever to make 
sure the transmission is on the neutral position.

Summary of Contents for BJ250-18




















































Reviews:

No comments