Quatra™ Full-Rise Scissor Lift
19
P/N 5900085 — Rev. A1 — October 2019
Align the Frames into Position
Once you have created the Chalk Line Guides, move the Frames into position.
To align the Frames into position
:
1.
Use a Forklift or Shop Crane to lower the Frames into the layout you created.
The Frames go on the
inside
of the Chalk Lines.
2.
Align the Base Plates with the Chalk Lines.
3.
Move the two Frames into position where the Left and Right Chalk Lines intersect the alignment
Chalk Line.
4.
Measure the distance between the two Platforms at point
a
and
b
.
The Frames need to be same distance apart at both points. If
a
and
b
are not the same, adjust the
Platform locations; make sure they are the same distance apart and parallel to each other.
5.
Double check that the Frames are correctly positioned and the Utility Rails are facing the inside of
the Lift.
Lift the Platforms off the Bases
You must raise the Platforms off their Bases in order to complete other aspects of the installation.
Be
sure to leave the Lift on a Safety Lock when you raise it.
⚠
WARNING
The Frames are extremely large and heavy. You must use a Forklift or Shop Crane
to move the Platform off the Bases; make sure the Safety Locks are engaged when
you reach the desired height.
To lift the Platforms off the Bases
:
1.
Use a Forklift or Shop Crane to raise the Platform off of its Base Plate, using care so that the Base
Plates do not move.
Make sure to hold down the Base while you raise the Platform.
Tip
Once the Platform and Base are separated by more than half an inch (~13 mm), you
can put Industrial Slings (straps) around each end to continue raising the Platform off
the Base.
2.
Raise the Platform to the first Safety Lock, then make sure the Frames are secure on a Locking
position.
⚠
WARNING
Do not leave or work on the Lift without first confirming that the Platforms are
secure on a locking position; if not, you or anyone else working on the Lift could be
seriously injured.
3.
Repeat the same procedure for the other Frame.
Important
:
Do not bolt down the Bases at this point
. This will be done later in the
installation process.
Summary of Contents for Quatra XR-12000L
