HD-7P / HD-7W Four-Post Lifts
17
P/N 5900041 — Rev. M — July 2019
Selecting a Location
When selecting the location for your Lift, consider:
•
Architectural plans
. Consult the architectural plans for your desired installation location. Make
sure there are no issues between what you want to do and what the plans show.
•
Available space
. Make sure there is enough space for the Lift: front, back, sides, and
above
.
Refer to
•
Overhead obstructions
. Check for overhead obstructions such as building supports, heaters,
electrical lines, low ceilings, hanging lights, and so on.
You do not want the Vehicles on the
Lift hitting obstructions
. The Lift location should have 87 inches of height plus the height of
the tallest Vehicle you plan on raising, if you want to make sure you do not hit anything overhead.
•
Side and front clearances
. You must leave room around the Lift. Leave at least six feet (72
inches / 1.8 meters) clear on both sides and the front of the Lift, and no obstructions at all at the
Rear of the Lift (so you can safely drive Vehicles onto the Runways).
•
Power
. You need an appropriate power source for the Power Unit.
•
Outdoor installations
. Your Lift is approved for
indoor
installation and use
only
.
•
Floor
. Only install the Lift on a flat, Concrete floor; do not install on asphalt or any other surface.
The surface must be level; do not install if the surface has more than three degrees of slope.
⚠
WARNING
Installing your Lift on a surface with more than three degrees of slope could lead to
injury or even death. Only install the Lift on a level floor. If your floor is not level,
consider making the floor level or using a different location.
•
Shimming
. If your Concrete floor is not completely level, you can use Shims under the bases of
the Posts, as needed, to level the Lift.
To estimate your Shim requirements, use a transit level and targets to check for flatness. Use the
provided Shims as necessary.
NOTICE
Do not shim a Post more than half an inch using the provided Shims and Anchor Bolts.
A maximum shim of 2 inches is possible by ordering optional Shim Plates. Contact
BendPak at
(800) 253-2363
, extension 191 to order.
•
Concrete specifications
. Do not install the Lift on cracked or defective Concrete. Make sure
the Concrete is at least 4.25 inches thick, 3,000 PSI, and cured for a minimum of 28 days. Do not
install Anchor Bolts within six inches of cracks or other defects in the Concrete.
⚠
CAUTION
BendPak lifts are supplied with installation instructions and Concrete anchors that
meet the criteria set by the current version of the American National Standard
“Automotive Lifts – Safety Requirements for Construction, Testing, and Validation”,
ANSI/ALI ALCTV. You are responsible for any special regional structural and/or
seismic anchoring requirements specified by any other agencies and/or codes such
as the Uniform Building Code (UBC) and/or International Building Code (IBC).
Be sure to check your Concrete floor for the possibility of it being a
post-tension slab
. In this
case, you must contact the building architect before drilling. Using ground penetrating radar may
help you find the tensioned steel.
⚠
WARNING
Cutting through a tensioned cable can result in injury or death. Do not drill into a
post-tension slab unless the building architect confirms you are not going to hit
tensioned steel or you have located it using ground penetrating radar.
If colored
sheath comes up during drilling, stop drilling immediately
.
Summary of Contents for HD-7P
