BendPak 5175238, Service Manual

Page: 33 / 41

14
17
13
16
15
2
12
7
6
11
8
3
1
5
10
9
4
18
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
NEXT ASSEMBLY
5215787
ITEM
NO
PART
NUMBER
DESCRIPTION QTY REV
1 5701266 HD-973P LOWER POWER SIDE RAMP 1 C
2 5746190 HD-7/7500/9 RAMP SHEAVE BUSHING 4 C
3 5755019 AIR LINE TROUGH Ø13.5 x Ø9.5 x 203 1 B
4 5735090 HD-7/7500/9 RAMP STRAP 1 C
5 5735702 HD-973 CYLINDER CLEVIS PLATE 1 A
6 5700359 HD-973P ROLLING BRIDGE BEAM 1 B
7 5735032
ROLLING JACK RAIL CLOSEOUT
2 C
8 5735028 PIN STOP 4 B
9 5755067 AIR LINE TROUGH Ø13.5 x Ø9.5 x 1750 1 A
10 5755068 AIR LINE TROUGH Ø13.5 x Ø9.5 x 2140 1 A
11 5700300 HYDRAULIC HOSE HOLDER 2 A
12 5755090 HD-7/7500/9 DRIVE UP RAMP HINGE TUBE 4 C
13 5736200 HD-7500/9 RAMP END PLATE, 4-SHEAVE 1 B
14 5736201 HD-7/7500/9 RAMP END PLATE, 2-SHEAVE 1 B
15 5736203 HD-7500/9/973 RIGHT RAMP BOLT PLATE, 4-SHEAVE 1 D
16 5736204 HD-7500/9/973 LEFT RAMP BOLT PLATE, 4-SHEAVE 1 D
17 5736202 HD-7/7500/9 RAMP BOLT PLATE, 2-SHEAVE 1 D
18 5701669 HD-973 LOWER POWER SIDE RAMP CYLINDER BRACKET 1 A
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
D
ADDED 5701669, MOVED 5735090 WAS 2397
NOW 2570, ADDED GLOSS NOTE TO PAINT,
REMOVED GRIT NOTE
04/13/2020 TM 01120
E
PLACEMENT OF 5755090: REMOVED WELD
FROM BOTTOM, SPECIFIED FULL WELD ON TOP,
WAS 66 TO CENTER NOW 56 MIN TO EDGE,
UPDATED BOM REVISIONS
12/09/2021 TM 01367
F ADDED DISTANCE TO AIR LINE TROUGH 09/23/2022 CA 01448
WHERE USED
HD-973P
SHEET 1 OF 4
REV DWG. NO.
A
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
F
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TM
5601270
HD-973P LOWER POWER
SIDE RAMP WELDMENT
06/28/2018
DO NOT SCALE DRAWING
1:25 SCALE:
THIRD ANGLE PROJECTION
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
NOTE: UNLESS OTHERWISE SPECIFIED.