XR-12000L & XR-12000AL Product Label Positioning
J
XR-12000Series-Lift_Console-Panel.pdf:
Size: 9.5”W x 9.5”H
Material: White Vinyl Pressure Sensitive Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 4/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate for abrasion, chemical, and ultra
violet protection
PN 5905715
XR-12000Series-Lift_Console-Panel-DIELINE.pdf:
• 1/2” radius corners
•
DOES NOT PRINT - For Die Cut ONLY
ALI/WL200_Label Kit
Will be placed by BendPak Santa Paula.
PN 5905103
L
K
ST_Motor_Tag.pdf:
Trim: 4”W x 2”H
Material: 2 Mil. White Adhesive Vinyl
Ink: U.V. protected CMYK 4/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate for abrasion, chemical, and ultra violet protection
HP:
VOLT:
VOLT:
Hz:
FLA:
FLA:
KVA:
PH:
FRAME:
SF:
EFF%:
TANK:
TYPE:
DES:
DATE:
CODE:
I.D. NO:
NOT THERMALLY PROTECTED
RPM:
MAX. AMB. ºC:
INS CLASS:
MADE IN CHINA
WARNING:
GROUNDINGS - Failure to connect the
motor frame to equipment grounding conductor by
using the grounding cord, green screw, or green
wire provided, may result in serious electric shock.
TENV
SKU NO:
www.rangerproducts.com
ENGINEERED BY
RANGER PRODUCTS USA
Ranger Products is a registered trademark of BendPak Inc.
BENDPAK
RANGER
PRV:
DUTY/DEVOIR:
USE APPROPRIATE TAG AS ASSIGNED
SAMPLE
M
ALI/WLSIA01_Label
PN 5905377
TO LOWER LIFT
3
Before lowering vehicle, be sure all personnel, tools and
equipment are clear of lift and surrounding area.
3
Raise lift by pressing RAISE button on power unit. Elevate
lift at least two inches to allow adequate clearance for locks
to clear.
3
Press and HOLD SAFETY LOCK RELEASE button.
3
Lower vehicle by pressing LOWER button on power unit until
lift has descended completely.
3
When lowering lift MAKE SURE that all personnel and objects
are kept clear of lift and surrounding area.
3
ALWAYS keep a visual line of site on lift AT ALL TIMES.
3
ALWAYS make sure that ALL LOCKS are disengaged. If one of
the locks inadvertently engages on descent, lift and/or vehicle
may disrupt causing serious injury or death.
1.
WARNING:
If any component of the lift
is found to be defective, DO NOT USE LIFT!
2. Never operate the lift with any person or
equipment below.
3. Never exceed rated capacity.
4. Always verify safety locks are engaged
before any attempt is made to work on or
near vehicle.
5. Never leave lift in an elevated position
unless all safety locks are engaged.
6. Do not permit electric motor to get wet!
Motor damage caused by dampness is not
covered under warranty.
7. Failure to read, understand and follow
these instructions may cause serious injury
or death.
WARNING
OPERATING INSTRUCTIONS
S
AF
ETY LOC
K
R
E L E A SE
LIFT
OPERATION
LOWER
1645 Lemonwood Dr. • Santa Paula, CA 93060
TEL: 805-933-9970 • www.bendpak.com
ENGINEERED BY BENDPAK USA • MADE IN CHINA
SAFETY
FIRST
RAISE
TO RAISE LIFT
3
Position vehicle’s center of gravity over center of lifting platforms.
3
Set parking brake and use wheel chock to hold vehicle
in position.
3
Before raising vehicle, be sure all personnel are clear of lift and
surrounding area. Pay careful attention to overhead clearances.
3
Raise lift to desired height by pressing RAISE button on
power unit.
3
Maintain visual contact with vehicle and surrounding area at
all times while raising or lowering lift.
3
STOP IMMEDIATELY
if load shifts or becomes unlevel.
3
After vehicle is raised to desired height, lower lift onto the
nearest safety locks.
3
ALWAYS ENSURE ALL PRIMARY SAFETY LOCKS ARE
ENGAGED
before entering work area.
PN 5905715
