![background image](http://html.mh-extra.com/html/bendpak/5175026/5175026_service-manual_2732359028.webp)
P-6B & P-6FB Product Decal Positioning
A
B
C
D
E
P-6FB_Operation_Instructions_5905813.pdf:
Trim: 15”W x 3”H
Material: White Vinyl Pressure Sensitive Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 2/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate for abrasion, chemical, and ultra
violet protection
1645 Lemonwood Dr., Santa Paula, CA 93060 • TEL: 805-933-9970 • www.bendpak.com • EnginEErED by bEnDPAk USA • MADE in ChinA
P-6_BendPak_Cylinder_Decal.pdf:
Material: Clear Adhesive PET
Size: 16”W x 3”H
Thickness: 4 Mil
Finish: Polished
Ink: U.V. protected, Opaque White
Print Process: Silk Screen, 85 line-screen
(Yellow color in file represents
what should be clear PET material and SHOULD NOT print as Yellow ink.
White area in file represents Opaque White ink.)
Lamination: Clear-gloss over-laminate for abrasion, chemical, and ultra
violet protection
WARNING
!
WARNING
!
WARNING
!
Read and understand all safety warnings and
operation procedures before using lift.
Keep hands and feet clear from moving parts.
OPERATION INSTRUCTIONS
TO RAISE LIFT:
•
Clear area of personnel and make sure lift is in full lowered
position.
•
Drive vehicle over lift making sure center line of the vehicle is
positioned properly over lift pads.
•
Position lift pads underneath the vehicle making sure that
they make secure contact with the factory recommended
lifting points.
TO LOWER LIFT:
•
Clear area before lowering lift.
•
Raise lift by pressing RAISE BUTTON on power unit. Elevate
lift at least two inches to allow adequate clearance for locks
to clear.
•
Press push button
AIR SAFETY VALVE
and
HOLD
.
•
Lower vehicle by pressing power unit lowering handle until
lift has descended completely.
•
When lowering lift
PAY CAREFUL ATTENTION
that all
personnel and objects are kept clear.
•
ALWAYS
keep a visual line of site on lift
AT ALL TIMES
.
•
ALWAYS
make sure that
ALL LOCKS
are disengaged. If one
of the locks inadvertently engages on descent, lift and/or
vehicle may disrupt causing personal injury or death.
DO NOT
park on, or load lift in a fully
lowered position or damage may result.
NEVER OVERLOAD LIFT
Check for 1” minimum clearance
between car and lift before raising.
Drive car completely over lift
Moving Machinery
Keep hands and feet
clear at all times
•
Before raising, make sure the weight of the vehicle does not
exceed rated capacity of lift.
•
Push the
RAISE
button to commence lifting.
•
Raise lift until the vehicles tires clear the floor.
•
Stop then check if vehicle is secure and the lifting pads are
still in contact with the frame.
•
Continue raising vehicle to desired height.
•
Raise until the
SAFETY LOCK BARS
drop into the
LOCKED
position.
•
Lower the lift until the
LOCK BARS
rests against the
LOCK
BLOCK
.
•
ALWAYS
make sure the safeties are engaged before
attempting to work on or near a vehicle.
PN 5905813
Product_Data_Label_5905940-New.pdf:
Size: 4.5”W x 2.3”H
Material: White Vinyl Pressure Sensitive Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 2/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen
or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate for abrasion,
chemical, and ultra violet protection
Cylinder_Warning-Red_5905176.pdf:
Size: 3”W x 3”H
Material: White Vinyl Pressure Sensitive Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 2/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen
or 300 p.p.i. for digital
Lamination: Clear-gloss over-laminate for abrasion,
chemical, and ultra violet protection
Label_Warning_Pinch_Point_Small-5905350.pdf:
Size: 15”W x 1.5”H
Material: White Vinyl Pressure Sensitive Adhesive
Thickness: 4 Mil
Ink: U.V. protected CMYK 4/C Process
Finish: Polished
Print Process: Offset Lithography - 200 line-screen or 300 p.p.i.
for digital
Lamination: Clear-gloss over-laminate for abrasion, chemical, and
ultra violet protection
WARNING!
VERY IMPORTANT
TO PROLONG LIFE EXPECTANCY
OF CYLINDER SEALS AND
PREVENT PREMATURE LEAKAGE
AND WEAR, RAISE LIFT TO FULL
HEIGHT AT LEAST ONCE A DAY.
ALSO, THIS IS AN EFFECTIVE
WAY TO BLEED ANY TRAPPED
AIR AND MAINTAIN EQUAL
LIFTING OF THE SYSTEM.
PN 5905176
PN 5905940
PN 5905813
PN 5905350
PN 5905176
Clear PET material and
SHOULD NOT print as Yellow