manualshive.com logo in svg

BENDIX EC-15 ANTILOCK CONTROLLER ASSY, Manual

Share
Download
BENDIX EC-15 ANTILOCK CONTROLLER ASSY Manual Download Page 22

22

IGNITION OFF. REMOVE CONNECTOR(S) FROM EC-15

™

CONTROLLER. MEASURE RESISTANCE BETWEEN THE
APPROPRIATE SPEED SIGNAL (+) AND SIGNAL RETURN (-).
RESISTANCE FOR BENDIX

®

 WS-20

™

 SENSOR IS BETWEEN

1500-2500 OHMS. REFER TO VEHICLE MANUAL FOR THE
RESISTANCE VALUES IF OTHER THAN WS-20

™

 SENSOR

IS IN USE. (REFER TO FIGURE 7 & 8)

DISCONNECT CONNECTOR AT SPEED SENSOR
INSPECT THE CONNECTOR, THEN CHECK THE
RESISTANCE BETWEEN TWO PINS ON SENSOR.
RESISTANCE BETWEEN 1500-2500 OHMS FOR THE
BENDIX

®

 WS-20

™

 SPEED SENSOR.

REPLACE THE SENSOR

YES

REPLACE EC-15

™

CONTROLLER

NO

TROUBLESHOOTING

SECTION VI PART B - TESTING THE WHEEL SPEED SENSOR

ARE ANY LED’S ILLUMINATED?

CORRECT RESISTANCE?

START HERE FROM

SECTION VII  PART A

NO

YES

GO TO SECTION III “INSPECTION

FOR ILLUMINATED LEDS”

REPAIR OR REPLACE SPEED

SENSOR WIRING HARNESS.

ARE SAME RED LED’S ILLUMINATED?

REPEAT THE “INITIAL

START-UP PROCEDURE”

NO

YES

NO

YES

SAME  LED’S ILLUMINATED?

GO TO SECTION III “INSPECTION

FOR ILLUMINATED LEDS”.

NO

YES

RECONNECT CONNECTOR AT SPEED

SENSOR AND EC-15

™

 CONTROLLER

AND DO MAGNETIC RESET. NOTE IF

ANY RED LEDS ARE ILLUMINATED.

Summary of Contents for EC-15 ANTILOCK CONTROLLER ASSY

























Reviews:

No comments

Brands by name

Popular brands

Load more brands