manualshive.com logo in svg

Bender A-Isometer IRDH 275, Operating Manual

Share
Download
Bender A-Isometer IRDH 275 Operating Manual Download Page 61

Technical data IRDH275(B)

61

TGH1361en/11.2009

General data

EMC immunity ................................................................................................................. acc. to EN 61326
EMC emission .................................................................................................................. acc. to EN 61326
Shock resistance IEC 60068-2-27 (device in operation) ...................................................... 15 g  / 11 ms
Bumping IEC 60068-2-29 (during transport)......................................................................... 40 g  / 6 ms
Vibration resistance IEC 60068-2-6 (device in operation)..............................................1 g / 10...150 Hz
Vibration resistance IEC 60068-2-6 (during transport) ..................................................2 g / 10...150 Hz
Ambient temperature (during operation) ........................................................................-10 °C...+55 °C
Storage temperature range ...............................................................................................-40 °C...+70 °C
Climatic class acc. to IEC 60721-3-3 .................................................................................................... 3K5
Operating mode....................................................................................................... continuous operation
Mounting ........................................................................................................  as indicated on the display
Connection ........................................................................................................................ screw terminals
Connection, rigid, flexible............................................................................ 0.2...4 mm

2

 /  0.2...2.5 mm

2

Connection, flexible with connector sleeve,  without/with plastic sleeve ......................  0.25...2.5 mm

2

Conductor sizes (AWG)..................................................................................................................... 24-12
Tightening torque  .......................................................................................................................... 0.5 Nm
Protection class, internal components (DIN EN 60529) ..................................................................... IP30
Protection class, terminals (DIN EN 60529)........................................................................................ IP20
Type of enclosure ................................................................................................  X112, free from halogen
DIN rail mounting ....................................................................................................................... IEC 60715
Flammability class ......................................................................................................................  UL94 V-0
Software version IRDH275 ........................................................................................................ D160 V1.4
Software version IRDH275B ...................................................................................................... D159 V1.4
Weight approx. .................................................................................................................................. 510 g

Option „W“

Shock resistance IEC 60068-2-27 (Device in operation)......................................................  30 g / 11 ms
Bumping IEC 60068-2-29 (during transport).........................................................................  40 g / 6 ms
Vibration resistance IEC 60068-2-6 ...........................................................................1.6 mm / 10...25 Hz

...........................................................................................................................................4 g / 25...150 Hz

Ambient temperature (during operation) ........................................................................-40 °C...+70 °C
Storage temperature range ...............................................................................................-40 °C...+85 °C
Screw mounting ...............................................................................................................................2 x M4

The values marked with * are absolute values

Summary of Contents for A-Isometer IRDH 275













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands