![background image](http://html1.mh-extra.com/html/beltronics/belbel-rx75/belbel-rx75_manual_2730757002.webp)
Note:
1. Connection between the radar receiver, and the receiver cable,
must be located in a dry location under hood.
2. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
4. Do not splice cable.
Laser “Blocking” Cables
1
Route Laser Receiver cable to firewall, and secure with zip-ties
(included).
2
Route Laser cable into the vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or 7/16" hole.
3
Pull cable through firewall, and plug connector into jack marked
“Front Laser/Blocker” on Interface.
4
Pull grommet (located on cable) through the firewall to seal the
hole. Use silicone sealant (not supplied) if necessary.
Note:
1. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
3. Do not splice cable.
Front Radar Receiver
1
Determine the best location for the Radar
Receiver. The best location is typically under
the bumper, or inside the front grill of the
vehicle. For the best radar performance,
install the Radar Receiver horizontally, with a
clear “view” of the road.
2
Using the built-in mounting holes on the
Receiver, or the supplied right-angle mounting
bracket, mark location. Drill pilot holes in the
vehicle if necessary.
3
Mount Radar Receiver using the supplied
hardware. (If right-angle mounting bracket is
used, secure Radar Receiver to the right-
angle bracket first, then install bracket with
Radar Receiver to the vehicle.)
Note:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
Front Laser “Blocking” Module
1
Determine best location for the Laser Receiver.
For optimum performance, install the Laser Receiver
near the front license plate if possible, with a clear “view” of the road.
2
Using the supplied mounting bracket, mark location. Drill pilot
holes in the vehicle if necessary.
3
Mount the Laser Blockers using the supplied hardware, making
sure that it is level to the road.
Note:
1. Do not drill holes in the Laser Receiver itself.
2. Thoroughly investigate location before drilling any holes.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.)
4. Do not splice cable.
5. Make certain that the Laser Blocker is level, and has a
clear “view” of the road.
WARNING
Laser Blockers MUST be mounted level (+/-5 degrees) to the road to
work properly.
Radar “Blocking” Cable
1
Connect the receiver cable to the receiver.
2
Route cable to firewall, and secure with zip-ties (included).
3
Route receiver cable into the vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or 7/16" hole.
4
Pull cable through firewall, and plug connector into the jack labeled
“Front Radar” on the Interface.
5
Pull grommet (located on the receiver cable itself) through the
firewall to seal the hole. Use silicone sealant (not supplied) if necessary.
Installation Manual
D
F
User Display
1
Determine the best location for the User Display in the
vehicle’s interior. (Consult customer if necessary.)
2
Install User Display using supplied velcro, or double-sided tape.
3
Route
cable
and plug into jack marked “Display” on Interface.
Note:
1. Make certain that the User Display is clearly visible from the
driver’s position, and that the controls can be easily accessed
without interfering with normal driving.
Interface
1
Install Interface under the dash using supplied zip-ties.
DO NOT MOUNT IN ENGINE COMPARTMENT.
2
Connect black wire (–) to ground, and red-striped wire (+) to a
switched 12-volt supply. (If
BEL
Pro Remote Plus
is left in the “on”
position, it will automatically power on and off with the ignition).
Use blue 3M connector (provided) to tap into existing circuit if
needed.
3
Radar Receiver, front Laser Receiver, rear Laser Receiver, and
Display Controller all plug into the Interface. (Be sure to plug all
cables into the correct labeled jacks.)
A
B
C
M O D E L R X 7 5 P L U S
E
BEL
BEL
Rear Laser “Blocking” Module
1
Remove two license plate screws,
(top or bottom).
2
Mount Laser Receiver to plate using
supplied mounting bracket.
3
Route wire through trunk compartment,
and into the vehicle’s interior.
4
Insert connector to jack labeled “Rear
Laser Receiver” on Interface.
TIPS
1. Do not block license plate illumination.
2. Do not cover any required license plate
information.
INSTALLATION ALTERNATIVES:
1. Cable can be routed under vehicle
(keep away from hot and moving parts)
then brought into the vehicle’s interior.
2. Cable can be cut if necessary for
routing. Reconnect and solder each of
the three wires, and seal with heat-
shrink tubing.
Remote Mute/Volume Adjust
1
Determine best location for the
Remote Mute Button.
2
Clean surface area.
3
Remove paper backing on the back of
the button, and press onto surface.
4
Route cable and plug into jack marked
“Mute” on Interface.
Test
After all components are installed correctly:
1
Turn vehicle’s ignition to the “on” position.
2
Turn
BEL
Pro Remote Plus
on by pressing the Power button.
3
BEL
Pro Remote Plus
will cycle through a startup sequence.
4
If any error messages come up, see appropriate section of
the Owner’s Manual for details.
External Speaker
1
Install the amplified speaker in the
desired location using the supplied
mounting bracket and hardware.
2
Snap the amplified speaker into the
bracket.
3
Attach the red ( + ) wire to a switched
power supply in the vehicle.
4
Attach the black ( – ) wire to chassis
ground.
5
Insert the 3.5mm plug into the external
speaker jack on the 5 pin interface
connector.
Interior of V
ehicle
12 Volt
Power
Line
FR
ON
T
RE
A
R
F
H
C
D
B
A
G
I
G
B
Y-Connector
E
H
I
22292_Bel ProRemote_Manual 11/20/06 11:52 AM Page 2