background image

 

 
Belshaw Brothers Inc.    1750 22

nd

 Avenue S.   Seattle, WA  98144-4590     Phone (206) 322-5474    Fax: (206) 322-5425  

Revised 04/04/2006 

                      US/Canada/Mexico Limited Warranty  

       Page 1 

 

 

US/Canada/Mexico Limited Warranty and Return Policy 

 

Belshaw Brothers Inc. warrants parts of its manufacture and assembly of equipment to be free from 
defects in workmanship and material which would result in product failure under normal use and 
service.  Belshaw’s entire liability under this Warranty is limited to either repairing or replacing at its 
factory or; on user’s premises, at Belshaw’s option, any equipment or parts thereof, which shall be 
determined by Belshaw to be defective.  If necessary to return parts to the factory they must be shipped 
transportation charges prepaid

.  This shall be purchaser’s sole and exclusive remedy. 

 

Belshaw reserves the right to make changes in design; or add any improvement, at any time without 
incurring any obligations to install, the same, on equipment previously sold. 
 

This warranty is expressly in lieu of any and all other warranties express or implied, including: 
implied warranties of merchantability and fitness for any particular purpose, and all other 
obligations or liabilities what so ever on Belshaw’s part.  All statutory or implied warranties, 
other than title, are expressly nullified and excluded. 
 
Belshaw neither assumes nor authorizes any person to assume for it any obligation or liability 
in connection with the sale of Belshaw’s products or parts thereof. 
 

Possession, use/or operation of equipment, or parts sold hereunder for any other than their designed 
purpose, or use of equipment which is in poor repair, modified, improperly operated, or neglected is 
done at the owner’s risk.  Belshaw hereby disclaims any liability for these actions and shall not be liable 
for defects in or for any damages or loss to the property sold which is attributable to such actions. 
 

Under no circumstances shall Belshaw be liable for any indirect, special, incidental, or 
consequential damages arising out of, or from the use of Belshaw’s product by buyer, it 
assignees, employees, agents or customers. 
 

Belshaw makes no express warranties except those contained in this Warranty concerning the product 
sold hereunder.  No modification or alteration of this Warranty shall be made except by Belshaw in 
writing. 
 

Warranty Period / Guidelines 

This limited warranty shall extend for a period of one year from date of shipment and to the original 
owner only. It covers parts (manufactured by Belshaw) and labor. This warranty covers only items sold 
within the United States, Canada and Mexico. A pre-authorization must be obtained from Belshaw 
before any warranty work is carried out, failure to do so may void the warranty of the product. 

 

Limited Warranty

 

With respect to parts not manufactured by Belshaw, warranty coverage shall be limited to the original 
part manufacturer’s warranty, or the Belshaw limited warranty, whichever is the lesser coverage period.  
In no case will the warranty be in excess of 18 months after date of shipment of the equipment.  

 

Replacement parts provided under the terms of this warranty are warranted for the remainder of the 
original warranty period applicable to the product. 

Summary of Contents for 718LCG











































Reviews: