Bell System BSX Installation & Operation Manual Download Page 31 | Manualshive

Page: 31 / 32

background image

BSX Isolated Audio Entry System

PD-142 Issue 1

Installation and Operating Manual

Page 31 of 32

Safety Information and Declarations

Connections to the 240VAC mains supply must be carried out by a qualified electrician or
similar competent person, and made in accordance with current legislative requirements.
A two-pole switch (as provided by a Consumer Unit or Switch-Fuse) must be included to
isolate both Live and Neutral during Installation or Maintenance. The circuit must be
protected by a fuse or other current-limiting device, rated according to the capacity of the
cable used, up to a maximum of 10A. Use only mains cable to BS6004 or equivalent,
within the following specified limits:

Min

Max

Conductor Diameter 1.0mm (0.8mm2) 2.25mm (4mm2)
Cable Diameter

4.0mm

8.0mm

BSX2 Control Cabinet

The cabinet must be in a protected indoor environment, close to a 240V electrical supply,
e.g.  an electrical cupboard.  Connections to the 240V AC mains supply must be carried
out  by  a  qualified  electrician  or  similar  competent  person,  and made  in  accordance  with
accepted safety practices.  The cabinet should be fed from a two-pole switch (as provided
by a Consumer Unit or Switch-Fuse) to isolate both Live and Neutral during Installation or
Maintenance.  The circuit must be protected by a current limiting fuse or other device with
a maximum rating of 5A.
The cabinet power supply is protected by a fuse; always replace this with the correct type
and rating as indicated on the power supply.

Earthing

A good mains safety earth must be connected to the cabinet and Power Supply.
The cabinet back-plate complete with all the equipment is normally removed to allow the
cabinet to be fixed to the wall. When replacing this back-plate ensure that the earth
bonding and any flexible earthing wires are properly reconnected.

Battery

Care  must  be  taken  to  ensure  the  battery  terminals  are  not  shorted  together  by  metal
objects  as  this  may  constitute  a  Fire  Hazard.    Observe  the  correct  polarity  when
connecting:
Red wire

-

Positive

Black wire

-

Negative

The Battery is protected by a fuse, always replace this with the correct type and rating as
indicated on the power supply.

«
...
29
30
31
32
»

Summary of Contents for BSX

































Reviews:

No comments

Related manuals for BSX

Brand: a/d/s/ Pages: 14

Brand: M-E Pages: 20

Brand: M-Audio Pages: 12

Brand: Zip Pages: 16

Brand: Panasonic Pages: 4

Brand: CAME BPT Pages: 16

Brand: Martin Audio Pages: 1

Brand: Veeder-Root Pages: 699

Brand: Rain Bird Pages: 2

Brand: Commax Pages: 14

Devicenet R7F4DD-DA16A-H

Brand: M-system Pages: 7

Unitel DI-623-21L

Brand: Axema Pages: 16

Brand: Guardian Audio Pages: 4

Brand: Vidos Pages: 8

Brand: Harman Pages: 30

Brand: Opus Pages: 34

Varixx UMS 4401 SPCD

Brand: Grundig Pages: 47

Brand: Bauhn Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands