background image

 

 

 

UK24MOD

 

Belimo Gateway MP to Modbus RTU 

 

www.belimo.com 

T9-

UK24MOD • en • v1.7 • 02.2014 • Subject to changes 

17 / 20 

 

 

Version overview 

 

Firmware V1.08 

New functions/modifications: 

 

Bug fix: Modbus telegrams longer than 20 Bytes (e.g. ReadHoldingRegister with more 
than 8 registers) are properly handled 

 

Bug fix: Detection of new MP actuator in operation 

Firmware V1.07 

New functions: 

 

New register for reading of nominal volumetric flow 

 

Support for MPL actuators 

Note on compatibility: 

  Service information can be found in registers 1001 to 1004 (former 161 to 164) 

 

Known issues: 

  Modbus telegrams longer than 20 Bytes (e.g. ReadHoldingRegister with more than 8 

registers) cause wrong register entries. 

Firmware V1.06 

New functions: 

  Timeout period for fire & smoke increased from 60 to 120 seconds (Register 2). 

Higher numbers of nodes realizable per Modbus master. 

Firmware V1.05 

New functions: 

  New registers for adjusting Min (14) and Max (15) setting. 

  New register for reading of absolute volumetric flow. 

 Firmware V1.04 

New functions: 

  Parity/Character transmission adjustable via DIP switch: 

NONE (1, 8, N, 2) or EVEN (1, 8, E, 1) 

Firmware V1.03 

Release without restrictions 

 

Summary of Contents for UK24MOD





















Reviews: