Belden Hirschmann OWL LTE M12 User Manual Download Page 71

Page: 71 / 153

Configuration

4.9 OpenVPN Tunnel Configuration

Select the

OpenVPN

item to configure an OpenVPN tunnel. The menu item will expand and

you will see four separate configuration pages:

1st Tunnel

2nd Tunnel

3rd Tunnel

and

4th

Tunnel

. The OpenVPN tunnel function allows you to create a secure connection between two

separate LAN networks. The router allows you to create up to four OpenVPN tunnels. IPv4 and
IPv6 dual stack is supported.

Item

Description

Specifies the description or name of tunnel.

Protocol

Specifies the communication protocol.

•

UDP

– The OpenVPN communicates using UDP.

•

TCP server

– The OpenVPN communicates using TCP in

server mode.

•

TCP client

– The OpenVPN communicates using TCP in

client mode.

•

UDPv6

– The OpenVPN communicates using UDP over

IPv6.

•

TCPv6 server

– The OpenVPN communicates using TCP

over IPv6 in server mode.

•

TCPv6 client

– The OpenVPN communicates using TCP

over IPv6 in client mode.

UDP/TCP port

Specifies the port of the relevant protocol (UDP or TCP).

Remote IP Address

Specifies the IPv4, IPv6 address or domain name of the opposite
side of the tunnel.

Remote Subnet

IPv4 address of a network behind opposite side of the tunnel.

Remote Subnet Mask

IPv4 subnet mask of a network behind opposite tunnel’s side.

Redirect Gateway

Adds (rewrites) the default gateway. All the packets are then sent
to this gateway via tunnel, if there is no other specified default
gateway inside them.

Local Interface IP
Address

Specifies the IPv4 address of a local interface.

For proper rout-

ing it is recommended to fill-in any IPv4 address from local
range even if you are using IPv6 tunnel only.

Remote Interface
IP Address

Specifies the IPv4 address of the interface of opposite side of
the tunnel.

For proper routing it is recommended to fill-in

any IPv4 address from local range even if you are using IPv6
tunnel only.

Remote IPv6 Subnet

IPv6 address of the remote IPv6 network. Equivalent of the

Re-

mote Subnet

in IPv4 section.

Remote IPv6 Prefix

IPv6 prefix of the remote IPv6 network. Equivalent of the

Remote

Subnet Mask

in IPv4 section.

Local Interface
IPv6 Address

Specifies the IPv6 address of a local interface.

Continued on next page

UM Configuration OWL LTE M12

Rel. 06.1.09 - 07/2019

Summary of Contents for Hirschmann OWL LTE M12


























































































































































Search results

Summary of Contents for Hirschmann OWL LTE M12

Reviews:

Related manuals for Hirschmann OWL LTE M12

Brands by name

Popular brands

Belden Hirschmann OWL LTE M12, User Manual

Search results

Summary of Contents for Hirschmann OWL LTE M12

Reviews:

Related manuals for Hirschmann OWL LTE M12

Brands by name

Popular brands