background image

 

 

 

 

In case there is hum or ground noise, check that the RCA/XLR switch is in the correct position for the type of 
connection being used. 

 

 

Ensure that the preamplifier or any source components are not producing hum by setting the preamplifier 
to a MUTE or Standby setting. 

 

 

The design of the REF1000

M

 reduces the chance for ground loop induced hum, but we still recommend 

using shorter interconnect cables to the preamplifier. Connect all power cables to a common outlet box or 
power conditioner unit to reduce the possibility for ground current noise being induced into the audio signal 
path. 
 

 

If you choose to power your source and preamplifier components from a different AC supply than used for the 
REF1000

M

 amplifiers, we recommend that you use a high quality balanced XLR cable driven from a true 

balanced XLR preamplifier output.  

 

 

We

 

do not recommend

 that you resort to ‘cheater plugs’ or some other means to disconnect the power 

ground from the REF1000

M

 as this may lead to dangerous operation and void the warranty. 

 

 

The small blue LED lamp indicates that power is connected to the REF1000

M

 and that the power switch is in 

the ON position. If the amplifier detects a fault or short circuit in the output connections then it will go into a 
protection mode and stop playing. If this occurs toggle the power switch to the OFF position and check the 
speaker cabling to ensure that no speaker output is either shorted together or connected to a ground. When 
you are certain that the loudspeaker cabling is correct, power the unit ON again, check that the blue LED is lit 
and that music will play. 

 

 

There is an internal fuse protection on the REF1000

M

. If the power switch is in the ON position, the power 

cable is connected to a functioning power outlet at the correct voltage and the blue LED is not lit, this 
indicates that the internal fuse may have blown. If this occurs contact your dealer, distributor or Bel Canto for 
service. There are no user replaceable fuses or other parts. Opening the chassis will void your warranty. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for REF1000m











Reviews: