background image

9.  Operation

9.1  Warning notices

DANGER

Operation outside the permissible limit range!

Operation of the product and accessories outside the permissible limits and operating 

parameters, unauthorised intervention and modifications may result in death or serious 

injury.
• 

Adhere to the limits and operating parameters specified on the type plate and in the 

manual.

•  Adhere to the assembly conditions and ambient conditions.
•  Check whether the operating parameters have been amended or restricted by the use of 

accessories. 

•  Adhere to the maintenance intervals.

DANGER

Electric voltage!

There is a danger of death or serious injuries as well as malfunction and device failure 
following contact with components which are in contact with electric voltage.
•  Only operate the product with the cover or housing complete and closed.

NOTE

Operating personnel!

Insufficient knowledge of the product and the accessories can lead to damage to property 

and the environment as well as impair operation.
• 

The product and accessories may only be operated and used by qualified operating 

personnel.

BEKOMAT

®

 32iU

Original installation and operation manual

42 | 68

Summary of Contents for 32iU





































































Reviews: