background image

9 / EN

Washing Machine / User’s Manual

Adjusting Rear Feet

•  When you turn the knob (visible in the circle) 

in the direction of the arrow, the machine 

will be elevated by 0.3 mm. When you turn 

it in the opposite direction of the arrow, the 

machine will be lowered by 0.3 mm.

•  You can check your machine‘s rear 

and front feet via water gage for correct 

adjusment.

•  Do not adjust the rear feet by using 

chargeable devices. Use a screwdriver 

instead.

Adjusting the feet with water level

•  You must remove the Detergent Drawer to 

set the Water Level.

•  For the system to operate properly, the 

bubble inside the Water Level must be in 

the 

middle

.

•  If the bubble inside the Water Level is on the 

left

, the pre-set 

right

 foot of the Washing 

Machine must be adjusted.

•  If the bubble inside the Water Level is on the 

right

, the pre-set 

left

 foot of the Washing 

Machine must be adjusted.

•  If the bubble inside the Water Level is at 

the 

back

, the pre-set 

front

 feet of the 

Washing Machine must be turned to the left 

(clockwise).

•  If the bubble inside the Water Level is at the 

front

, the pre-set 

front

 feet of the Washing 

Machine must be turned to the right (anti-

clockwise).

4.1.7 Electrical connection

Connect the product to a grounded outlet 

protected by a 13 A fuse. Our company shall 

not be liable for any damages that will arise 

when the product is used without grounding in 

accordance with the local regulations.
•  Connection must comply with national 

regulations.

•  The wiring for the electrical outlet circuit 

must be sufficient to meet the appliance 

requirements. Use of a Groud Fault Circuit 

Interrupter (GFCI) is recommended.

•  Power cable plug must be within easy reach 

after installation.

•  If the current value of the fuse or breaker 

in the house is less than 13 Amps, have a 

qualified electrician install a 13 Amp fuse.

•  The voltage specified in the “Technical 

specifications” section must be equal to 

your mains voltage.

•  Do not make connections via extension 

cables or multi-plugs.

A

 CAUTION!

•  Damaged power cables must be replaced 

by the Authorised Service Agents.

Electrical requirements 

Before you insert the plug into the wall socket 

make sure that the voltage and the frequency 

shown in the rating label corresponds to your 

electricity supply.
We recommend that this appliance be 

connected to the mains supply via a suitable 

switched and fused socket in a readily 

accessible position.
Should the mains lead of the appliance 

become damaged or need replacing at any 

time, it must be replaced by a special purpose 

made mains lead which can only be obtained 

from a Authorised Service Agent.

B

 WARNING!

•  This appliance must be earthed

If the fitted moulded plug is not suitable for 

your socket, then the plug should be cut off 

and an appropriate plug fitted.

Summary of Contents for WTIK76151F













































Reviews: