manualshive.com logo in svg

Beko VRT 95929 VI, User Manual, Page: 11 / 32

Share
Download
Beko VRT 95929 VI User Manual Download Page 11

11 / EN

Cordless Stick Vacuum Cleaner / User Manual

3 Installation

3.1 Intended use

This appliance is intended for household use and it is not suitable for industrial use.

3.2 Installation of the mobile charging dock

1

2

Install charging dock tube (16) to 
the charging dock support (17), 
then install the charging dock (15) 
to the charging dock tube (16).

Install the thin end of the charger to 
the seat on the charging dock (15).
Plug the charging adaptor (19) to 
the outlet.

1

2

102-104 cm

1

2

If you want to install the charging 
dock (15) to the wall, detach 
the charging unit from the tube 
(16) and support (17) using two 
separate buttons.

Position the charging dock (15) at 
a height of 102-104 cm from the 
ground.

Install the end of the charging 
adaptor (19) to the seat on the back 
of the charging dock (15).
Put the cord of the charging 
adaptor through the power cord 
securing ring behind the charging 
dock tube and secure the cord.
Install the charging dock (15) to the 
wall using two screws (24) and two 
dowels (25).

Summary of Contents for VRT 95929 VI

































Reviews:

No comments