10
Preparation and start
1. Sort the laundy according to cottons, synthetics,
etc.
2. Put laundry in the drum and close the door.
3. Turn the appliance on by pressing On/Off button
4. Set the programme selector knob to desired
programme.
5. Press the Start/Pause/Cancel button. Programme
starts and the drying indicator light comes on.
Changing the programme
When changing to a
different
programme the
current programme must be cancelled first.
To do so first press the Start /Pause/Cancel button
for 3 sec. in order to cancel the programme.
Cancelling a programme
Do not turn the appliance off during the heating
phase while progress indicator is on. Risk of heat
accumulation is possible in clothing! Fire Risk!
1. First stop the running programme (press the Start
/Pause/Cancel button. Then press it again for 3
seconds to cancel the programme
2. Set the programme selector to
Freshen Up
3. Press the Start /Pause/Cancel button to start the
programme.
4. Wait for the programme to end.
Adding more laundry
Only add additonal clothing at the begining of a
drying cycle, otherwise the result will be a mixture
of damp and too dry textiles.
1. Press Start /Pause/Cancel button. Start/Stop
indicator will flash.
2. Put laundry in the drum and close the door.
3. Press the >Start /Pause/Cancel < button. Start/Stop
indicator will be on.
Laundry final drying
In order to reach desired dryness level you can
use additional final drying using one of the timed
programmes.
If the dryness level is not satisfactory set the
programme selector to one of the timed programmes
60min, 40min, 20min or 10min.
Programme end
The programme cycle is completed when the
indicators >End/Anti-Creasing< and >Clean filter< are
illuminated.
Throughout the anti-crease stage the indicator
>End/Anti-Creasing< flashes. The programme can
then be ended at any time.
1. Set the On/Off button to off position.
2. Open door, remove laundry, check drum for
foreign objects.
3.
After every drying cycle :
– Clean the fluff filter (see “Fluff filter”). (Page 14)
- Empty condensed water tank (see “Emptying
Tank”) (Page 5)
4.
After approx. 20 drying cycles or four times a
year
– Clean the condenser.
– Clean sensor ribs.
5.
When required
– Clean housing and fascia using a soft cloth and
a mild soap; wipe dry with a soft cloth.
Do not use scrubbers and scrubbing powders!
These will damage the plastic parts and painted
surfaces.
When the door is opened during the programme,
the programme will pause automatically and the
start button light will flash. Close the door and
press the start button to continue the programme.
Drain hose connection
The water arising from drying (“condensed water”)
is normally collected in the condensed water
container, which needs to be emptied after every
drying cycle.
• The condensed water can also be drained
permanently by means of the drain hose supplied
into a siphon trap or any other drain.
In that case the condensed water container
needs no longer to be drained –nevertheless the
»Reservoir full « indicator will light at the end of
each drying cycle.
Important:
• In order for the water to run off observe the
maximum hose length and highest point above
the floor (see“Specifications”)!
• Ensure that there are no sharp bends in the hose!
Here’s how to proceed:
1. At the rear of the appliance, Water drain
connections, Pull off the white hose by hand. DO
NOT USE PLIERS.
2. Push the drain connecter into the hose on the
machine and drain hose firmly. Run the drain hose
to the waste outlet of a washbasin and connect it.
hose connector
Drain hose connector
Water pipe (white ) from
water collection container
to water tank
3. If the drain hose is hung to the edge of a
washbasin or bathtub, secure it against slipping
off.
For this installation please contact your Beko
Customer Service.
practical usage tips, preparation and starting a program
