background image

36

Dishwasher / User’s Manual

/39 EN

Troubleshooting

•  Detergent is added long before the washing process. >>> Pay attention to add 

detergent shortly before start-up of the washing.

•  Opening of the detergent dispenser lid is prevented during washing. >>> Place the 

dishes in a way that will not prevent the detergent dispenser lid from opening and the 

water going into the machine from impellers.

•  Detergent is stored under unsuitable conditions. >>> If you are using powder detergent, 

do not store the detergent package in humid places. Keep it in a closed container if 

possible. For ease-of-storing, we recommend you to use tablet detergents.

•  Impeller holes are clogged. >>> Lower and upper impeller holes might be clogged with 

food remnants such as lemon pips. Clean the impellers regularly as illustrated in section 

“Cleaning and Care”.

Decorations and ornaments on kitchen utensils are being erased.

C

Decorated glasses and decorated lustre porcelains are not suitable for washing 

in the dishwasher. Manufacturers of some glassware and porcelain tableware 

items do not recommend washing such kitchen utensils in the dishwashers 

either.

Dishes are scratched.

C

Kitchen utensils that contains or are made of aluminum should not be washed in 

dishwasher.

•  Salt leakage exists. >>> Pay attention not to spill salt around the salt filling hole while 

adding salt. Spilled salt can cause scratches. Make sure that the salt reservoir lid is tightly 

closed after finishing the filling process. Run the prewash programme to remove the salt 

that spilled inside the machine. Since the salt granules that will remain under the lid will 

dissolve during prewash, causing the lid loosen, check the lid once again at the end of 

the programme.

•  Water hardness setting is low or salt level is insufficient >>> Measure the hardness of 

the supply water appropriately and check the water hardness setting.

•  Dishes are not placed orderly in the machine. >>> When placing the glasses and other 

glassware into the basket lean them not against other dishes but the edges or racks of 

the basket or the glass support tines. Striking of the glasses to each other or to other 

dishes due to the impact of water during washing can cause breaks, or scratches on their 

surfaces.

A smear remains on glasses that resembles milk stain which can not be 

removed when wiped by hand. A bluish / rainbow appearance occurs when 

the glass is pointed to light.

•  Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled rinse aid when 

adding rinse aid.

Summary of Contents for DFN16X10










































Reviews: