background image

NOTE

Please be sure to use the accessories provided by our company to install this electric 

water heater. This electric water heater can not be hung on the support until it has been 

confirmed to be firm and reliable. Otherwise, the electric water heater may drop off from 

the wall, resulting in damage of the heater, even serious accidents of injury. When 

determining the locations of the bolt holes, it shall be ensured that there is a clearance 

not less than 0.2m on the right side of the electric heater, to convenient the maintenance 

of the heater, if necessary.

7

4. METHODS OF USING

NOTE

During normal operation, the inlet valve shall be always kept open.

First, open any one of the outlet valves at the outlet of the water heater, then, open the inlet 

valve. The water heater gets filled with water. When water flows out of the outlet pipe it implies 

that the heater has been filled fully with water, and the outlet valve can be closed.

Insert the supply plug into the supply socket, the indicator will light up this time.

The thermostat will automatically control the temperature. When the water temperature inside 

the heater has reached the set temperature, it will switch off automatically, when the water 

temperature falls below the set point the heater will be turned on automatically to restore the 

heating.

Check the power plug and outlet as often as possible. Secure electrical contact and also proper 

grounding must be provided. The plug and outlet must not heat excessively.

If the heater is not used for a long time, especially in regions with low air temperature(below 0

), 

it is nessary to drain water from the heater to prevent damage of the water heater, due to water 

freezing in the internal tank.(Refer Cautions in this manual for the method to drain away the water 

from the inner container).

To ensure long reliable water heater operation, it is recommended to regularly clean the internal 

tank and remove deposits on the electric heating element of the water heater, as well as check 

condition (fully decomposed or not) of the magnesium anode and, if necessary, replace it with a 

new one in case of full decomposition.Tank cleaning frequency depends on hardness of water 

located in this territory. Cleaning must be performed by special maintenance services. You can 

ask the seller for address of the nearest service center.

 

5. MAINTENANCE

WARNING

Before doing any maintenance, please cut off the power supply.

!

Summary of Contents for BWH 100 LED











Reviews: