OPT-2-EXTIO-BFI, Extended I/O for BFI-P2/H3
By
Date
Revision
Revision date
Page
JSG
2020-06-23
-
-
1 (2)
Function
Optional card that extends the I/O of the inverter with 3 digital inputs and 1 relay output.
Compatible to BFI-P2/H3.
Extended I/Oy
- OPT-2-EXTIO-BFI
- Item number 63123
DECLARATION
All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means,
electrical or mechanical including photocopying, recording or by any information storage or retrieval system without
permission in writing from the publisher.
Copyright Beijer Electronics AB ©2020
The manufacturer accepts no liability for any consequences resulting from inappropriate, negligent or incorrect
installation. The contents of this User Guide are believed to be correct at the time of printing. In the interests of a
commitment to a policy of continuous improvement, the manufacturer reserves the right to change the specification
of the product or its performance or the contents of the User Guide without notice.
SAFETY
This option is specifically designed to be used with the BFI-P2/BFI-H3 variable speed drive product and is intended
for professional incorporation into complete equipment or systems. If installed incorrectly it may present a safety
hazard. The BFI-P2/BFI-H3 uses high voltages and currents, carries a high level of stored electrical energy, and is
used to control mechanical plant that may cause injury. Close attention is required to system design and electrical
installation to avoid hazards in either normal operation or in the event of equipment malfunction.
System design, installation, commissioning and maintenance must be carried out only by personnel who have the
necessary training and experience. They must read carefully this safety information and the instructions in this Guide
and follow all information regarding transport, storage, installation and use of the Option module, including the
specified environmental limitations.
Please read the SAFETY NOTICE carefully, and all Warning and Caution boxes elsewhere.
SAFETY NOTICES
WARNING
is given where there is a hazard that could lead to injury or death of personnel.
Within the European Union, all machinery in which this product is used must comply with the Directive 89/392/EEC, Safety of
Machinery. In particular, the equipment should comply with EN60204-1.
CAUTION
is given where there is a hazard that could lead to damage to equipment.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated
complies with the EMC legislation of the country of use. Within the European Union, equipment into which this
product is incorporated must comply with 89/336/EEC, Electromagnetic Compatibility.
WARNING
BFI-P2/BFI-H3
and the Option Modules should be installed only by qualified electrical persons and in accordance with local
and national regulations and codes of practice.
Electric shock hazard
! Disconnect and
ISOLATE
BFI-P2/BFI-H3
before attempting any work on it. High voltages are
present at the terminals and within the drive for up to 10 minutes after disconnection of the electrical supply.
Where the electrical supply to the drive is through a plug and socket connector, do not disconnect until 10 minutes have elapsed
after turning off the supply.
STANDARDS CONFORMITY
BFI-P2/BFI-H3 fitted with this Option complies with the following
standards:
-
CE-marked for Low Voltage Directive.
-
IEC 664-1 Insulation Coordination within Low Voltage Systems.
-
UL 840 Insulation Coordination for electrical equipment.
-
EN50081-2 EMC Generic Emissions Standard, Industrial Level.
-
EN50082-2 EMC Generic Immunity Standard, Industrial Level.
-
Enclosure ingress protection, EN60529 IP00, NEMA 250.
-
Flammability rating according to UL 94.
SPECIFICATIONS
-
Model Number: OPT-2-EXTIO-IN
-
Compatibility: BFI-P2 and BFI-H3
-
Digital Input x 3: 8-30V DC Input
-
Digital Input Response Time: < 8ms
-
Max Relay switching voltage: 250V
AC / 30V DC
-
Max Relay switching current: 6A
(250V AC) / 5A (30V DC)
-
Environmental: -10ºC … +50ºC
-
Conformity: IP20, UL94V-0
-
Terminal Torque: 0.5Nm (4.5 Ib-in)
