Beijer Electronics EXTER T100 Service And Maintenance Manual Download Page 18 | Manualshive

Page: 18 / 54

background image

Hardware

18

Beijer Electronics, MA00757A

3.4 Approvals and Enclosure Classes

EXTER K30m, EXTER K60c

EXTER T40/T40m

EXTER T60c/T60m

EXTER K70, EXTER K100
EXTER T70, EXTER T100

and EXTER T150

CE

EMC directive 89/336/EEC article 4.
The operator terminal conforms with the essential protection require-
ments in article 4 of the directive 89/336/EEC.
Noise tested according to EN61000-
6-3 emission and EN61000-6-2
immunity.

Noise tested according to EN61000-
6-4 emission and EN61000-6-2
immunity.

UL, cUL

UL 1604 Class I, Div. 2 (Electrical Equipment for Use in Class I, Division 2
Hazardous (Classified) Locations.
UL 508 (Industrial Control Equipment).
UL 50 (Indoor use).

DNV

Environmental test specification for instrumentation and
automation equipment: Standard for Certification No. 2.4.
Location classes: Temperature A, Humidity B, Vibration A, EMC B, Enclo-
sure C (panel front only).

Ingress
protection

IP 66/NEMA 4X (indoor use), UL 50 4X (indoor).

Back cover
protection
degree

IP 20.

Shock

IEC 60068-2-27 (15 g, 11 ms).

«
...
16
17
18
19
20
...
»

Summary of Contents for EXTER T100























































Reviews:

No comments

Related manuals for EXTER T100

Brand: Saitek Pages: 44

Minas A4 Series

Brand: Panasonic Pages: 5

Brand: Campbell Pages: 34

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

Brand: jablotron Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands