Behringer ULTRA-CURVE PRO DEQ Series Instructions Manual Download Page 5 | Manualshive

Page: 5 / 15

background image

5

Locate the ribbon cable which does not have a plug on the end.

Strip and tin the green, blue, violet, grey wires.

Solder:

Green to positive pad of C17
Blue to positive pad of C26
Grey to positive pad of C19
Violet to positive pad of C28

These wires feed the analog input XLR signals to the upgrade PCB.

«
...
3
4
5
6
7
...
»

Summary of Contents for ULTRA-CURVE PRO DEQ Series
















Reviews:

No comments

Related manuals for ULTRA-CURVE PRO DEQ Series

SACE Tmax XT Series

Brand: ABB Pages: 11

Brand: Landoll Pages: 52

Brand: JBSYSTEMS Light Pages: 14

Brand: Omnia Pages: 8

Brand: Labnet Pages: 2

Brand: Ecco Pages: 12

Brand: UMF Medical Pages: 12

Brand: Modulate Pages: 2

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: Jet Pages: 12

Brand: Parkside Pages: 58

Brand: Qu-Bit Electronix Pages: 15

Brand: Yamaha Pages: 29

Brand: Veit Brisay Pages: 18

Brand: Ocean Signal Pages: 2

RadioPRO 4 RP4-MZ11

Brand: PAC Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands