8
DR115DSP/DR112DSP/DR110DSP
Quick Start Guide
9
DR115DSP/DR112DSP/DR110DSP Controls
(1)
DSP display
- Backlit display for
DSP functions.
(2)
AUX IN
- Connect a media player via 1/8" TRS
cable. Stereo signals are summed to mono.
Control the input gain with the CH1 VOLUME
knob.
(3)
BLUETOOTH LED
- The blue LED will flash
when Bluetooth is on and searching for
connection. When successful connection is
established, the LED will light solid.
(4)
BLUETOOTH BUTTON
- Press to turn the
Bluetooth function on and off. Use the
MASTER control to adjust the volume.
(5)
OUTPUT
- Sends the combined signals from
CH1 and CH2 INPUTS out to another device via
XLR male connector.
(6)
VENTS
(7)
MASTER
- Rotate to control the overall
volume level. Push the knob to access
DSP functions, which are explained in the
following chapter.
(8)
CH1 VOLUME
- Rotate to adjust the gain
for INPUT 1 and AUX IN. The knob should
generally be set above the midway point for
microphone signals or turned down for line-
level signals.
(9)
CH2 VOLUME
- Rotate to adjust the gain
for INPUT 2. The knob should generally be
set above the midway point for microphone
signals or turned down for line-level signals.
(10)
CH1 INPUT
- Connect audio sources using
balanced XLR or ¼" cables.
(11)
CH2 INPUT
- Connect audio sources using
balanced XLR or ¼" cables.
(12)
POWER INPUT
- Connect a standard IEC
power cable. To replace a blown fuse,
carefully remove the fuse holder with a small
screwdriver, then replace the defective fuse
with a new one of the same type. Push the
fuse holder back into the slot until it snaps.
(13)
POWER SWITCH
- After all audio connections
have been made, flip the switch to the ON
position to turn the speaker on. (DR115DSP
only)
(14)
AUTO STAND-BY BUTTON
- Press to activate
the automatic standby function. When
activated, the speaker will automatically turn
off after 60 minutes without an input signal
present. When the unit receives a signal
again, the power will return automatically.
(DR112DSP/DR110DSP only)
(15)
AUTO STAND-BY LED
- The red LED will light
when the automatic standby function is
activated.
(16)
POWER BUTTON
- After all audio connections
have been made, press the button in to turn
the speaker on.
(DR112DSP/DR110DSP only)
(17)
FAN VENT
(1)
(6)
(5)
(4)
(3)
(2)
(12)
(7)
(8)
(9)
(10)
(11)
(17)
(14)
(16)
(15)
(1)
(6)
(5)
(4)
(3)
(2)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(16)
(15)
(14)
(1)
(6)
(5)
(4)
(3)
(2)
(6)
(7)
(8)
(9)
(10)
(11)
(13)
(12)
DR110DSP
DR112DSP
DR115DSP
Sound Programs
Press the MASTER knob twice to enter the speaker’s Sound Programs menu. ‘MUSIC’ will appear in the display. Press the MASTER knob again to select this program,
or turn the MASTER knob to scroll through the other options - ‘DJ’, ‘LIVE’, ‘SPEECH’. Press the MASTER knob to confirm your selection.
3-band EQ
Press the MASTER knob once and turn the MASTER knob to scroll through the 3-Band EQ menu: ‘HIGH EQ’ (treble), ‘MID EQ’ (mid range), ‘LOW EQ’ (bass). Press the
MASTER knob again to enter this frequency menu and turn the MASTER knob clockwise to boost the frequency up to 12 dB, or turn counterclockwise to reduce by
up to 12 dB. Press the MASTER knob to confirm your settings.
High Pass Filter
Press the MASTER knob once and turn the MASTER knob until ‘SUB’ appears in the display. Press the MASTER knob again to enter the speaker’s High Pass Filter
(low cut) menu. Turn the MASTER knob to select between OFF 80, 100, 120 or 150 Hz, and press the MASTER knob again to confirm the selection. Audio below the
selected frequency will be attenuated.
Delay
Press the MASTER knob once and turn the MASTER knob until DELAY appears, then press the MASTER knob again to edit this function. This function causes the
signal to be delayed a small amount of time to allow the music to be played in time with speakers located further away (e.g. main speakers on stage plus additional
speakers in a balcony).
LED Mode
Press the MASTER knob once and turn the MASTER knob until LED MODE appears, then press the MASTER knob to edit this function. Select ‘ON’ to always show a lit
LED on the front panel while the speaker is powered on, or ‘OFF
’
to turn the LED off. Select ‘LIMIT
’
to allow the LED to indicate when either the HF or LF limiter has
engaged.
DSP Functions
