manualshive.com logo in svg

Behlen Country AHW100, Manual, Page: 6 / 8

Share
Download
Behlen Country AHW100 Manual Download Page 6

F-20201-2 

 

Rev. 1-101-9  11-4-04

STEP 5

Replace the 

Cover to 

complete the 

cleaning of 

the Valve.

STEP 3

If the Rubber Seal is grooved but 

still pliable (not hard and brittle), 

you may 

fl

 ip it over and use the 

backside of the seal. If both sides 

of the Seal are hard, replacement 

Seals are available. In some 

instances both the Plunger 

and the Seal may need to be 

replaced.

STEP 2

Clean the Rubber Seal in the 

Plunger and opening to the 

Valve of any mineral deposits 

or dirt buildup that may 

be obstructing the normal 

operation of the Valve.

Rubber Seal is

inserted inside Plunger 

Rubber Seal

Plunger 

Upper Arm

Plunger

w/seal 

Cover

Pins

STEP 1

Slide off Cover, 

pivot Upper 

Arm up, and 

remove the 

Plunger.

Upper 

Arm

Lower 

Arm

Pins

STEP 4

Replace the Plunger with the nipple facing 

out, and the rubber facing the valve. Pivot 

Upper Arm down over Plunger.

Float

Float Arm

Thumb

Screw

Complete 

Assembly

Instructions for Cleaning the MC Valve

and Replacing the Plunger & Seal

Summary of Contents for AHW100









Reviews:

No comments