background image

TROUBLE SHOOTING #1

5. 

••• IM  PORTANT • CHAIN .... 

Befo re this step, make sure to 

leed the chain on the outside 

of the piston stem roller (see 

yellow arrow). Il lelt in its proper 

position, it wil/ not be possible to 

insert the handle pin and chain, 

breakage may occur. 

Align handle holes with pump 

housing holes and push through 

handle pin (see red arrow) 

7. 

Pull down on the handle to 

release the tension on the safety 

pin. 

CAREFULLY 

remove  the 

safety pin. 

9. 

Once the chain is in the proper 

position, check to see that it 

moves freely and that it is not 

obstructed. 

11, 

Pump the lever a few times to 

raise the forl<s. Put the up/down 

lever to its 

NEUTRAL 

position. 

Using a 14mm wrench and a 

flat screwdriver, adjust the valve 
cam so that the forl<s don't /ower 

or rise (il handle is pumped) at 

this position. 

6. 

Make sure that handle pin is 

completely through the handle 

and resting on the other side. 

8. 

Feed the chain and nut first back 

inside the handle  THROUGH the 

handle pin's center hole. 

... IMPORTANT - TIP••• 

Release the up/down lever to 

its lowest posilion to make the 

process easier. 

10. 

Using bath hands, 

push on the valve 

cam to raise the 

hook inside the 

housing and leed 
the end of the 

chain in the cam. 

(see image at 

right) 

12. 

••• IMPORTANT· FINAL CHECK •• • 

Test all the features of the pallet 

truck before this step.  The handle 

should be pumped with full strokes 

to prime and eliminate air in the 

system.  The up/down lever shou/d be 

checked at the handle 's lowest posi 

Uon for this puts the most tension 

on the chain. Once the pallet truck is 

adjusted properly and is perforrning 

wel/, drive in the second spring pin 

using a hammer. 

Summary of Contents for ACBF














Reviews: