BEER Uno Top Cold Operation Manual Download Page 22

 

Beer Grill AG 

 

Beer Grill GmbH 

 

Allmendstrasse 7 

Tel. +41 (0)56 618 7800 

Körnerstrasse 14 a 

Tel. +49 (0)71 61 659 876 

[email protected] 

CH 

– 5612 Villmergen 

Fax +41 (0)56 618 7849 

– 79539 Lörrach 

Fax +49 (0)71 61 659 879 

www.beergrill.com 

 

 

 

 

 

 

 

Seite 22 

12  Maintenance 

12.1  Service instructions 

In order to guarantee flawless functioning of the device and thus optimal presentation of the 
goods, the entire technology must be regularly checked and maintained. 

12.2  Normal maintenance 

The normal and preventative maintenance essentially consists of a weekly cleaning of all 
stainless  steel  parts,  which  have  to  be  cleaned  with  lukewarm  water  and  soap,  then  
thoroughly rinsed and carefully rubbed dry. Before doing this, however, the device must be 
disconnected from the power supply. 

12.3  Extraordinary maintenance 

Extraordinary  maintenance  is  carried  out  by  specialist  personnel  in  case  of  damage  or  
malfunctions, wherever possible disconnect the device from the power supply beforehand. 

Both  repairs  and/or  exchange  of  components  could  prove  to  be  necessary.  All  defective 
parts have to be exchanged exclusively with equivalent materials and components or those 
recommended by the manufacturer. 

 
 
 
 
 
 
 
 

 
 

12.4  Replacing the glasses 

The side panels must always be pushed in all the way to the support so that they do not 
come to rest on the stopping bar of the front panel holder. If they are resting on the stopping 
bar, the upper glass holder will be lifted too far so that the front glass panel can fall out if 
touched. 

The panels can be partly or completely lifted out of their holders for cleaning. 

Please insert the glasses exactly the way it is indicated on the drawings below: 
 
 

Figure 1 

Pull the sneeze screen forward 

(1)

 

 

Fit the front glass panel and turn it to the inside 

(2)

 

Push sneeze screen back into place 

(3)

 

 

If  the  user  exchanges  components  or makes  changes  to the  device  without 
written authorisation from the manufacturer, or uses non-authorised replace-
ment parts, the warranty is immediately void. 

i

 

Summary of Contents for Uno Top Cold





























Reviews: