4
5
TOOLS
GAS CYLINDER SAFETY
GAS CYLINDER SAFETY
GAS LEAK TEST PROCEDURE
TOOLS REQUIRED
Gas Cylinder Safety Information
This appliance is designed to be used with a gas cylinder not
exceeding 9KG (20lbs) capacity.
The Gas cylinder must be constructed and marked in
accordance with specifications for LP Gas Cylinders of
the:(USA) U.S. Dept. of Transportation (DOT) or the National
Standard of Canada, CAN/CSA - B339, Cylinders, Spheres or
Tubes for the transportation of dangerous goods.
The gas cylinder supply valve must be turned off when
the appliance is not in use. Gas cylinders must be stored
outdoors, out of reach of children and must not be stored in
a building, garage or any other enclosed area.
The gas cylinder used must incorporate a safety collar to
protect the valve assembly.
IMPORTANT!
When disconnecting and removing the gas cylinder for the
purpose of refilling, always observe the following procedure.
Ensure that all gas control valves on the appliance and the
gas cylinder are turned off before disconnecting the gas line
from the cylinder.
Do not smoke or use a naked flame near the appliance or
gas cylinder while disconnecting the gas line between the
appliance and gas cylinder.
Remove the gas cylinder from the enclosure before
disconnecting the gas line from the appliance.
Tighten all connections before placing the gas cylinder back
in its enclosure.
The Gas Leak Testing Procedure should be conducted every
time the gas cylinder is refilled and reconnected to the
appliance - before using the appliance.
Regulator connection (Fig 1 & 2)
1. Check that all control knobs are in the ‘Off’ position.
2. Make sure the cylinder valve is off by turning the valve
knob clockwise.
3. Remove the protective cap from the cylinder if present.
4. Leak test the connection with a soapy water solution
(See Gas Leak Testing Procedure)
Hose and regulator replacement must be a genuine part
specified for this appliance and is obtainable from your
nearest BeefEater stockist.
You will need the following tools to assemble your barbecue.
10mm Spanner (wrench) all body nuts
19mm Spanner (wrench) for gas inlet connection
Phillips Head Screwdriver
NOTE: Always use the correct size spanner (wrench) to
tighten gas fittings. Ensure that all gas fittings are spanner
tightened and then leak tested before continuing with
operation of the appliance.
FIG 4
Use the following procedure to check for gas leaks.
Never use a naked flame to check for gas leaks.
FIG 1
Standard POL regulator
FIG 2
Quick connect regulator
1. In a small container, mix up a solution of water and
detergent or soap. Mix the solution well.
2. For LPG make sure that the gas supply valve on the gas
cylinder is turned on. For Natural gas make sure that
the gas line is correctly fitted to the appliance.
3. Make sure that the gas control valves on the appliance
are all turned off.
4. Using a brush or spray bottle apply the solution to the
gas line and each join in the gas line. See Fig 3.
5. Bubbling of the solution will indicate that there is a
leak present.
6. Re-tighten or re-seal any joints that are leaking.
7. If a leak persists then contact your distributor or the
manufacturer for assistance.
FIG 3
Gas shutoff valve
Gas shutoff valve
Bleeder valve screw
Bleeder valve screw
Protector cap
Protector cap
Gas cylinder
Gas cylinder
Regulator and hose
Regulator and hose
Tighten in this direction
Tighten in this direction
IMPORTANT!
Always check the gas label on the appliance to ensure that
you have the correct gas configuration.
FIG 5
For Your Safety
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odour continues, immediately call your gas supplier or
your fire department.
For Your Safety
1. Do not store or use gasoline or other flammable vapours
or liquids in the vicinity of this or any other appliance.
2. An LPG cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
IMPORTANT!
• The cylinder supply system must be arranged for
vapour withdrawal. This normally means the cylinder
must be upright.
• Do not store a spare LP-gas cylinder under or near
this appliance.
• Never fill the cylinder beyond 80% full.
If these directions are not followed exactly, a fire causing
death or serious injury may occur.